Vision Automobile Electronics Industrial Co Ltd ZS5101US 사용자 설명서
7.
NoExternal Switch: If you need to add external switch function, please connect with
ZS5101 for extending detection. The ZS5101 has 2 normally closed contact
terminals. These can be used for additional external switch wired contacts. The
external switch will send an alarm report (type: 07, level: 0xFF) by opening the
window/door.
ZS5101 for extending detection. The ZS5101 has 2 normally closed contact
terminals. These can be used for additional external switch wired contacts. The
external switch will send an alarm report (type: 07, level: 0xFF) by opening the
window/door.
Operation
1.
Vibrate the ZS 5101, sensor will send status of
“ON”(Basic Set,Value:0xFF) & alarm
report (type:07, level:0Xff) to any associated nodes. With no triggered in 10
seconds, the senor will send status of
seconds, the senor will send status of
“OFF”(Basic Set,Value:0x00) & alarm report
(type:07, level:0x00)
2.
Normal operation, the LED will not light.
3.
The ZS 5101 sensor equipped with tamper switch. If the cover of sensor is removed,
the ZS 5101 will send an alarm report (type:07,level:0xFF) to the Z-Wave™
Interface Controller, and the LED will go solid.
the ZS 5101 will send an alarm report (type:07,level:0xFF) to the Z-Wave™
Interface Controller, and the LED will go solid.
Federal Communications Commission Statement
This equipment has been followed to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
and correct the interferene by one of the following measures:
Reorient or relocate the receiving antenna,
Increase the separation between the equipment and receiver,
Connect the equipment into and outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undersired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
and correct the interferene by one of the following measures:
Reorient or relocate the receiving antenna,
Increase the separation between the equipment and receiver,
Connect the equipment into and outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undersired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user
’s authority to operate this equipment.
Limited Warranty
Vision Guarantees that every wireless shock sensor is free from physical defects in material and
workmanship under normal use for one year from the date of purchase. If the product proves
defective during this one-year warranty period, Vision will replace it free of charge. Vision does not
issue any refunds. This warranty is extended to the original end user purchase only and is not
transferable. This warranty does not apply to : (1) damage to units caused by accident, dropping or
abuse in handling, or any negligent use; (2) units which have been subject to unauthorized repair,
taken apart, or otherwise modified; (3) units not used in accordance with instruction; (4) damages
exceeding the cost of the product; (5) transit damage, initial installation costs, removal cost, or
reinstallation cost.
workmanship under normal use for one year from the date of purchase. If the product proves
defective during this one-year warranty period, Vision will replace it free of charge. Vision does not
issue any refunds. This warranty is extended to the original end user purchase only and is not
transferable. This warranty does not apply to : (1) damage to units caused by accident, dropping or
abuse in handling, or any negligent use; (2) units which have been subject to unauthorized repair,
taken apart, or otherwise modified; (3) units not used in accordance with instruction; (4) damages
exceeding the cost of the product; (5) transit damage, initial installation costs, removal cost, or
reinstallation cost.
-3-
Installation & Operation Manual
ZS 5101 EU
ZS 5101 US
ZS 5101 BR
ZS 5101 JP
ZS 5101 IN
Wireless Shock Sensor
ZS 5101
V0
1011123
6B1Z-51001