Mascot Electric Co. Ltd. GT-3 사용자 설명서
LINE
AF OUT
CHANNEL
MIC 2
MIC
SQ
MIXING
ON
OFF
AF OUT
MIC 1
LINE
MIC
CHANNEL
DC INPUT
12V 500mA
SQ
PWR
AF
RF
AF
RF
WIRELESS
SETTING UP
9
4
PRODUCT DESCRIPTION
WIRELESS
5.1.3 Dual Channel, Mini Case
Non Diversity, Front Fixed Antenna
7. Setting Up
NOTICE: Prior to setting up, please check that the transmitter and receiver are tuned to
the same frequency. Two or more transmitters operating in the same
frequency can not be used at the same time and area. So for each extra
transmitter, please select a different frequency which can be used
simultaneously at local area.
frequency can not be used at the same time and area. So for each extra
transmitter, please select a different frequency which can be used
simultaneously at local area.
7.1 Connecting the receiver to power
Check that the voltage of the supplied AC adapter conforms to the voltage available
(AC110 or 220) in local area. Using the wrong AC adapter may cause irreparable
damage to the unit.
damage to the unit.
Plug the feeder cable of the supplied AC adapter into DC IN socket on the receiver.
Then plug the AC adapter into a power outlet.
7.2 Connecting the receiver to an audio mixer or an amplifier
In order to make sure the sound quality and avoid distortion, please adjust the MIC/LINE
switch according to following instructions.
switch according to following instructions.
When using a standard audio cable with XLR or 6.3
ϕ phone plugs to plug into the MIC IN
on the audio mixer or on the amplifier, please select the MIC/LINE switch to “MIC”
position, the output level for unbalanced output is about at 100mV.
position, the output level for unbalanced output is about at 100mV.
When using a standard audio cable with XLR or 6.3
ϕ phone plugs to plug into the LINE
IN on the mixer, please select the MIC/LINE switch to “LINE” position, the output level for
unbalanced output is about at 1V.
unbalanced output is about at 1V.
For RS-80:
When select the MIC/LINE switch to “MIC”, please use a standard 6.3
ϕ plug cable to
connect the UNBALANCED connector on the receiver rear panel to an unbalanced
MIC. input on the audio mixer or on the amplifier,
MIC. input on the audio mixer or on the amplifier,
When select the MIC/LINE switch to “MIC”, please use a standard 3-pin XLR cable to
connect the BALANCED connector on the receiver rear panel to an balanced MIC.
input on the audio mixer or on the amplifier.
input on the audio mixer or on the amplifier.
When select the MIC/LINE switch to “LINE”, please use a standard 6.3
ϕ plug cable to
connect the UNBALANCED connector on the receiver rear panel to an unbalanced
line input on the audio mixer or on the amplifier.
line input on the audio mixer or on the amplifier.
When select the MIC/LINE switch to “LINE”, please use a standard 3-pin XLR cable to
connect the BALANCED connector on the receiver rear panel to an balanced line
input on the audio mixer or on the amplifier.
input on the audio mixer or on the amplifier.
For RS-60 / RS-120:
When select the MIC/LINE switch to “MIC”, please use a standard 6.3
ϕ plug cable to
connect the UNBALANCED connector on the receiver rear panel to an unbalanced
MIC. input on the audio mixer or on the amplifier,
MIC. input on the audio mixer or on the amplifier,
When select the MIC/LINE switch to “LINE”, please use a standard 6.3
ϕ plug cable to
connect the UNBALANCED connector on the receiver rear panel to an unbalanced
line input on the audio mixer or on the amplifier.
line input on the audio mixer or on the amplifier.
Never use the balanced and unbalanced audio outputs at the same time! This may
cause signal loss or increased noise.
cause signal loss or increased noise.
12
8
9
10
7
11
1
2
3
5