Yaesu Musen Co. Ltd. 20251X50 사용자 설명서
FT-2000
Operating Manual
Vertex Standard Co., Ltd.
44
engage the use of the [SUB VFO-B] knob for Amateur band selection. The “My Bands”
feature allows you to select several Amateur bands, and make
feature allows you to select several Amateur bands, and make
only
those bands
available for selection via the [SUB VFO-B] knob.
This feature can be
This feature can be
very
useful in a contest, where the 10/18/24 MHz band are not used,
or if you do not have antennas for some bands.
“My Bands” Setup
1. Press the [MENU] button to engage the Menu mode.
2. Rotate the Main Tuning Dial knob to select Menu item “121 tun MY BAND.”
3. Rotate the [SUB VFO-B] knob to choose a band that you wish to
“My Bands” Setup
1. Press the [MENU] button to engage the Menu mode.
2. Rotate the Main Tuning Dial knob to select Menu item “121 tun MY BAND.”
3. Rotate the [SUB VFO-B] knob to choose a band that you wish to
skip
(omit) from
the band-selection loop (when using the [SUB VFO-B] knob for band selection).
The available choices are 1.8/3.5/7/10/14/18/21/24/28/50/GE (General Band)/AU
(Transverter).
The available choices are 1.8/3.5/7/10/14/18/21/24/28/50/GE (General Band)/AU
(Transverter).
4. Press the [ENT] button to set the omission command to ON. “E” (Enable) notation
at the right of the band notation change to “d” (disable).
5. Repeat steps 3 and 4 to select/deselect as many bands as you like.
Note: The “ON” command sets the selected band to be
skipped
, while the “OFF”
command sets the selected band to be
included
in the band-selection list. Return
“d” notation to “E.”
6. Press and hold in the [MENU] button for two seconds to lock in the new
configuration and exit to normal operation.
Advice: “My Band” feature is effected to both the Main (VFO-A) and Sub (VFO-B)
bands.
“My Band” Operation
1. Press the (VFO-A) [BAND] button; the imbedded LED will glow Red, if you operate
bands.
“My Band” Operation
1. Press the (VFO-A) [BAND] button; the imbedded LED will glow Red, if you operate
the “My Band” feature on the Main band (VFO-A).
Advice: If the “My Band” feature on the Main band (VFO-A) seems not to be
operating, check see if the orange lamp to the right of the [SUB VFO-B] knob is
illuminated. If so, pressing the [A/B] key will cause the orange lamp to the right of
the [SUB VFO-B] knob to go out. Now, press the (VFO-A) [BAND] button to begin
“My Band” feature.
Advice: If the “My Band” feature on the Main band (VFO-A) seems not to be
operating, check see if the orange lamp to the right of the [SUB VFO-B] knob is
illuminated. If so, pressing the [A/B] key will cause the orange lamp to the right of
the [SUB VFO-B] knob to go out. Now, press the (VFO-A) [BAND] button to begin
“My Band” feature.
2. Press the (VFO-B) [BAND] button; the imbedded LED will glow Orange, if you
operate the “My Band” feature on the Sub band (VFO-B).
3. Rotate the [SUB VFO-B] knob to choose the Amateur band on which you wish to