Digital Security Controls Ltd. 08GS3060L 사용자 설명서

This equipment GS3060 is fixed and shall be installed by Service Persons only (Service Person is defined as a
person having the appropriate technical training and experience necessary to be aware of hazards to which that
person may be exposed in performing a task and of measures to minimize the risks to that person or other persons).
It shall be installed and used within an environment that provides the pollution degree max 2, over voltages
category II, in non-hazardous, indoor locations only. This manual shall be used with the Installation Manual of the
alarm control panel. All instructions specified within that manual must be observed.

Description

This GS3060 manages transmissions to a central station and can simulate the land line in the event
of trouble (land line down) or even substitute the land line completely in areas where the GSM
service is provided and a land line is not available.

The GS3060 has the capability of communicating alarm signals via the GPRS data network. The capability
enables a fast reliable path to central stations equipped with a Sur-Gard System III or System II receiver.
By connecting a GS3060 to a control panel's standard PSTN interface, telephone based Contact ID
signals are decoded and seamlessly routed through the GPRS network to any of the compatible receiver
options. When configured accordingly, the GS3060, upon line failure, instead of using GPRS, can also
connect the call on the GSM voice channels call based on the panel dialed number.

The performance of the GS3060 depends greatly on GSM network coverage, therefore, it should not
be mounted without first performing placement tests to determine the best location for reception
(minimum one green LED is ON). Optional antenna kits are available.

The GS3060 requires enrollment with CONNECT 24 to operate. Dealer application forms and
additional information on the CONNECT 24 Voice Response Unit (VRU) and web user-interface
can be found at www.connect24.com or at the following telephone numbers:

USA 1-888-251-7458

CANADA 1-888-955-5583

For UL Residential Fire and Burglary installations, the GS3060 is listed as a primary (sole)
communication means or as a back-up when used in conjunction with a POTS line (dialer).

For UL Commercial Burglary installations, the GS3060 is listed for supplementary (back-up) use in
conjunction with a POTS line (dialer).

The GS3060 shall be powered from any compatible listed control unit or compatible listed power
supply that provides an output voltage within the range of 9-14V

. The power supply shall be listed

for burglary applications and provide a minimum of 4h standby power capabilities. Example of
suitable listed compatible control unit is DSC Model PC1864 with AUX output rated 11.1 – 12.6V

Example of suitable listed Power Supply is DSC Model PC5404 with AUX output rated 11.6 – 12.6V

For ULC Commercial Fire Monitoring installations the GS3060 is listed as a passive communication
system when used in conjunction with a POTS line (dialer). Fire alarms shall be sent simultaneously
over both communication methods (GSM network and PSTN).

For ULC Commercial Burglary installations the GS3060 is listed as a passive communication system
with communication line security level P2 when used in conjunction with a POTS line (dialer).

For ULC Residential Fire and Burglary installations the GS3060 is listed as a primary (sole)
communication means or as a back-up when used in conjunction with a POTS line (dialer).

ATTENTION: The GS3060 is equipped with a cur

The GS3060 is equipped with a cur

The GS3060 is equipped with a currrrrrent limiter that limits cur

ent limiter that limits cur

ent limiter that limits currrrrrent demand on the

ent demand on the

12VDC power Input to 120 mA. The cur

12VDC power Input to 120 mA. The currrrrrent limiter is enabled by default (see Par

ent limiter is enabled by default (see Par

ent limiter is enabled by default (see Part# 8 in

t# 8 in

'Identification of Par

'Identification of Parts" on page 3) with JP3 in the OFF position. The cur

ts" on page 3) with JP3 in the OFF position. The cur

ts" on page 3) with JP3 in the OFF position. The currrrrrent limiter can be

ent limiter can be

disabled (bypassed) with jumper JP3 in the ON position. When the GS3060 12VDC power

disabled (bypassed) with jumper JP3 in the ON position. When the GS3060 12VDC power
input is supplied by the Alar

input is supplied by the Alar

input is supplied by the Alarm Panel Aux+ output, DSC r

m Panel Aux+ output, DSC r

m Panel Aux+ output, DSC recommends that the cur

ecommends that the cur

ecommends that the currrrrrent limiter

ent limiter

be active to limit the demand fr

be active to limit the demand from the panel. If the Alar

om the panel. If the Alar

om the panel. If the Alarm panel is intended to supply all of the

m panel is intended to supply all of the

cur

currrrrrent demand, you must ensur

ent demand, you must ensur

ent demand, you must ensure that the panel can supply 500mA and that the cur

e that the panel can supply 500mA and that the cur

e that the panel can supply 500mA and that the currrrrrent limiter

ent limiter

is disabled. When the GS3060 transmits, the cur

is disabled. When the GS3060 transmits, the currrrrrent demand exceeds 120 mA (500mA). with

ent demand exceeds 120 mA (500mA). with

the cur

the currrrrrent limiter in place, the additional cur

ent limiter in place, the additional cur

ent limiter in place, the additional currrrrrent demand is supplied by the GS3060 batter

ent demand is supplied by the GS3060 batter

ent demand is supplied by the GS3060 battery

y.....

NOTE: W

NOTE: With the cur

ith the cur

ith the currrrrrent limiter active, ther

ent limiter active, ther

ent limiter active, there is a risk of dischar

e is a risk of dischar

e is a risk of discharging the GS3060 batter

ging the GS3060 batter

ging the GS3060 battery when

y when

transmission fr

transmission frequency is high.

equency is high.

equency is high. The back-up batter

The back-up batter

The back-up battery must always be connected to the device

y must always be connected to the device

when the cur

when the currrrrrent limiter

ent limiter

ent limiter is ON.

is ON.

If the GS3060 Power is supplied by an Exter

If the GS3060 Power is supplied by an External Power Supply (13.8 V_, ±2%, 1A), the cur

nal Power Supply (13.8 V_, ±2%, 1A), the cur

nal Power Supply (13.8 V_, ±2%, 1A), the currrrrrent

ent

limiter must be disabled to allow the full cur

limiter must be disabled to allow the full currrrrrent demand to be supplied fr

ent demand to be supplied fr

ent demand to be supplied from the Power

om the Power

Supply

Supply. In this configuration the GS3060 batter

. In this configuration the GS3060 batter

. In this configuration the GS3060 battery is not r

y is not r

y is not requir

equir

equired.

ed.