Silitek Corporation R97SK 사용자 설명서
Make ID Connection of Wireless Keyboard (when interference is perceived)
(1) Press any key on the keyboard that you intend to use to establish communication between the
receiver and keyboard.
(2) Press the ID Connect button on the Receiver to ‘lock’ the received default keyboard ID. The
LED is turned ON.
The Wireless Mouse ID Code
The Wireless Mouse window (shown on the right) appears after the driver installation and the
computer reboot. Changing the ID code allows you to use a new Wireless Mouse without changing
the channel on the Receiver. Procedure as follows.
Initialize ID Connection at installation: Move the Wireless Mouse for a few seconds to establish
communication. Click on the selection of Connect ID to allow the unique ID code of your mouse to
be recognized. You may click on the selection of Exit if no any
other RF pointing devices are within 3 meters range.
Make ID Connection of Wireless Mouse
(1) Press [Shift + Alt + F11] or [Shift + Alt + F12] to call up the
Wireless Mouse ID Code window.
(2) Move the Wireless Mouse for a few seconds to establish a
connection, then click Connect ID .
(3) The new ID code is recognized and the Wireless Mouse window closed automatically.
Frequently Asked Questions:
1.
Q: Why the keyboard (or mouse) doesn’t work?
A: Check the Channel switch position. The position (1 or 2) on the keyboard (or Mouse) has to
A: Check the Channel switch position. The position (1 or 2) on the keyboard (or Mouse) has to
be the same as of on the receiver.
2.
Q: Why the mouse movement is not smooth.
A: The current channel may be interfered. You may change the channel or establish the ID code
A: The current channel may be interfered. You may change the channel or establish the ID code
from above mentioned procedure. Possible interference sources may include your
microwave oven, DECT wireless phone, wireless LAN, and any other devices operated at
the 27 MHz frequency band.
microwave oven, DECT wireless phone, wireless LAN, and any other devices operated at
the 27 MHz frequency band.
3.
Q: Why the keyboard LED is red?
A: The batteries in the keyboard are running out of power. Please replace new batteries.
A: The batteries in the keyboard are running out of power. Please replace new batteries.
FCC GUIDE LINES
WARNING: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, Uses
and can radiated radio frequency energy and if not installed and used in accordance with the
instructions," may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, Uses
and can radiated radio frequency energy and if not installed and used in accordance with the
instructions," may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with emission limits.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Shielded interface cables must be used in order to comply with emission limits.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Printed in China © Copyright Lite On Group - Silitek Corporation 2002; v1.1
Microsoft and Windows are trademarks or registered trademarks of the Microsoft Corporation in the
United States, other countries or both.
Microsoft and Windows are trademarks or registered trademarks of the Microsoft Corporation in the
United States, other countries or both.