MICROCHIP TECHNOLOGY INC. BM62S2 사용자 설명서
BM62 Regulatory Compliance Information
Preliminary
Revision 0.3 5/2016
DS60001372C-Page 54
APPENDIX A: CERTIFICATION
NOTICES
BM62 module regulatory approval status:
• BT SIG/QDID: in Progress
• United States/FCC ID: A8TBM62S2 (in Progress)
• Canada/IC ID: 12246A-BM62S2 (in Progress)
HVIN: BM62SPKS1MC2
• Europe/CE: in Progress
• Japan/MIC: in Progress
• Korea/KCC: in Progress
• Taiwan/NCC No: in Progress
• China/SRRC: in Progress
A.1
REGULATORY APPROVAL
This section outlines the regulatory information for the
BM62 module for the following countries:
BM62 module for the following countries:
• United States
• Canada
• Canada
• Europe
• Japan
• Korea
• Taiwan
• China
• China
A.1.1
UNITED STATES
The
BM62
module
has
received
Federal
Communications Commission (FCC) CFR47 Telecom-
munications, Part 15 Subpart C "Intentional Radiators"
modular approval in accordance with Part 15.212 Mod-
ular Transmitter approval. Modular approval allows the
end user to integrate the BM62 module into a finished
product without obtaining subsequent and separate
FCC approvals for intentional radiation, provided no
changes or modifications are made to the module cir-
cuitry. Changes or modifications could void the user's
authority to operate the equipment. The end user must
comply with all of the instructions provided by the
Grantee, which indicate installation and/or operating
conditions necessary for compliance.
munications, Part 15 Subpart C "Intentional Radiators"
modular approval in accordance with Part 15.212 Mod-
ular Transmitter approval. Modular approval allows the
end user to integrate the BM62 module into a finished
product without obtaining subsequent and separate
FCC approvals for intentional radiation, provided no
changes or modifications are made to the module cir-
cuitry. Changes or modifications could void the user's
authority to operate the equipment. The end user must
comply with all of the instructions provided by the
Grantee, which indicate installation and/or operating
conditions necessary for compliance.
The finished product is required to comply with all appli-
cable FCC equipment authorizations regulations,
requirements and equipment functions not associated
with the transmitter module portion. For example, com-
pliance must be demonstrated to regulations for other
transmitter components within the host product; to
requirements for unintentional radiators (Part 15 Sub-
part B "Unintentional Radiators"), such as digital
cable FCC equipment authorizations regulations,
requirements and equipment functions not associated
with the transmitter module portion. For example, com-
pliance must be demonstrated to regulations for other
transmitter components within the host product; to
requirements for unintentional radiators (Part 15 Sub-
part B "Unintentional Radiators"), such as digital
devices, computer peripherals, radio receivers, etc.;
and to additional authorization requirements for the
non-transmitter functions on the transmitter module
(i.e., Verification, or Declaration of Conformity) (e.g.,
transmitter modules may also contain digital logic func-
tions) as appropriate.
and to additional authorization requirements for the
non-transmitter functions on the transmitter module
(i.e., Verification, or Declaration of Conformity) (e.g.,
transmitter modules may also contain digital logic func-
tions) as appropriate.
A.1.2
LABELING AND USER
INFORMATION REQUIREMENTS
INFORMATION REQUIREMENTS
The BM62 module has been labeled with its own FCC
ID number, and if the FCC ID is not visible when the
module is installed inside another device, then the out-
side of the finished product into which the module is
installed must also display a label referring to the
enclosed module. This exterior label can use wording
as follows:
ID number, and if the FCC ID is not visible when the
module is installed inside another device, then the out-
side of the finished product into which the module is
installed must also display a label referring to the
enclosed module. This exterior label can use wording
as follows:
Contains Transmitter Module FCC ID:
A8TBM62S2
or
Contains FCC ID: A8TBM62S2
Contains FCC ID: A8TBM62S2
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation
A user's manual for the finished product should include
the following statement:
the following statement:
Additional information on labeling and user information
requirements for Part 15 devices can be found in KDB
Publication 784748 available at the FCC Office of Engi-
requirements for Part 15 devices can be found in KDB
Publication 784748 available at the FCC Office of Engi-
Note: This device has no been au orized as
required by the rules of the ederal Com-
munications Commission This device is
no and may not be, offered or sale or
leas
munications Commission This device is
no and may not be, offered or sale or
leas
or sold or leased, until au orization
is obtained
is equipment has been tested and found o comply
wi
he limi for a Class B digi l device pursuan o
pa 15 of the FCC Rule These limi s are designed
provide reasonable protection agains ha
ul
in
erence in a residential ins allation. his equip-
ment generate uses and can radiate radio fre-
quency energy and if no ins alled and used in
accordance wi h he in ru ions may cause harmful
in
quency energy and if no ins alled and used in
accordance wi h he in ru ions may cause harmful
in
erence to radio communic ions However
ere is no guaran ee hat in
nce will not occur
in a par icular in
lla ion his equipmen does
cause harmful in
nce to radio or television
recep io
which can be determined by urning the
equipment of and on, the user is encouraged to ry to
corre the in
corre the in
erence by one or more o the follow-
ing measures
• Reorien or reloca e he receiving an enn
• ncrease the separation between he equipment
and receiver
• Connec he equipmen in
an outlet on a circui
di eren from hat
which the receiver is con-
ne ed.
• Consult he dealer or an experienced radio
chnician for help.