MICROCHIP TECHNOLOGY INC. BM62S2 사용자 설명서
Preliminary
Revision 0.2 5/2016
DS60001372C-Page 55
BM62 Regulatory Compliance Information
neering and Technology (OET) Laboratory Division
Knowledge Database (KDB)
Knowledge Database (KDB)
http://apps.fcc.gov/oetcf/kdb/index.cfm
.
A.1.3
RF EXPOSURE
All transmitters regulated by FCC must comply with RF
exposure requirements. KDB 447498 General RF
Exposure Guidance provides guidance in determining
whether proposed or existing transmitting facilities,
operations or devices comply with limits for human
exposure to Radio Frequency (RF) fields adopted by
the Federal Communications Commission (FCC).
exposure requirements. KDB 447498 General RF
Exposure Guidance provides guidance in determining
whether proposed or existing transmitting facilities,
operations or devices comply with limits for human
exposure to Radio Frequency (RF) fields adopted by
the Federal Communications Commission (FCC).
From the FCC Grant: Output power listed is conducted.
This grant is valid only when the module is sold to OEM
integrators and must be installed by the OEM or OEM
integrators. This transmitter is restricted for use with
the specific antenna(s) tested in this application for
Certification and must not be co-located or operating in
conjunction with any other antenna or transmitters
within a host device, except in accordance with FCC
multi-transmitter product procedures.
This grant is valid only when the module is sold to OEM
integrators and must be installed by the OEM or OEM
integrators. This transmitter is restricted for use with
the specific antenna(s) tested in this application for
Certification and must not be co-located or operating in
conjunction with any other antenna or transmitters
within a host device, except in accordance with FCC
multi-transmitter product procedures.
A.1.4
HELPFUL WEB SITES
Federal
Communications
Commission
(FCC):
http://www.fcc.gov
FCC Office of Engineering and Technology (OET) Lab-
oratory
oratory
Division
Knowledge
Database
(KDB):
http://apps.fcc.gov/oetcf/kdb/index.cfm
A.2
Canada
The BM62 module has been certified for use in
Canada under Industry Canada (IC) Radio Standards
Procedure
Canada under Industry Canada (IC) Radio Standards
Procedure
(RSP)
RSP-100,
Radio
Standards
Specification (RSS) RSS-Gen and RSS-247. Modular
approval permits the installation of a module in a host
device without the need to recertify the device.
approval permits the installation of a module in a host
device without the need to recertify the device.
A.2.1
LABELING AND USER
INFORMATION REQUIREMENTS
INFORMATION REQUIREMENTS
Labeling Requirements for the Host Device (from Sec-
tion 3.1, RSS-Gen, Issue 4, November 2014): The host
device shall be properly labeled to identify the module
within the host device.
tion 3.1, RSS-Gen, Issue 4, November 2014): The host
device shall be properly labeled to identify the module
within the host device.
The Industry Canada certification label of a module
shall be clearly visible at all times when installed in the
host device, otherwise the host device must be labeled
to display the Industry Canada certification number of
the module, preceded by the words "Contains transmit-
ter module", or the word "Contains", or similar wording
expressing the same meaning, as follows:
shall be clearly visible at all times when installed in the
host device, otherwise the host device must be labeled
to display the Industry Canada certification number of
the module, preceded by the words "Contains transmit-
ter module", or the word "Contains", or similar wording
expressing the same meaning, as follows:
User Manual Notice for License-Exempt Radio Appara-
tus (from Section 8.4, RSS-Gen, Issue 4, November
2014): User manuals for license-exempt radio appara-
tus (from Section 8.4, RSS-Gen, Issue 4, November
2014): User manuals for license-exempt radio appara-
tus shall contain the following or equivalent notice in a
conspicuous location in the user manual or alterna-
tively on the device or both:
conspicuous location in the user manual or alterna-
tively on the device or both:
Transmitter Antenna (from Section 8.3, RSS-Gen,
Issue 4, November 2014): User manuals for transmit-
ters shall display the following notice in a conspicuous
location:
Issue 4, November 2014): User manuals for transmit-
ters shall display the following notice in a conspicuous
location:
Under Industry Canada regulations, this radio trans-
mitter may only operate using an antenna of a type
and maximum (or lesser) gain approved for the trans-
mitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotrop-
ically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
mitter may only operate using an antenna of a type
and maximum (or lesser) gain approved for the trans-
mitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotrop-
ically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
Conformément à la réglementation d'Industrie Can-
ada, le présent émetteur radio peut fonctionner avec
une antenne d'un type et d'un gain maximal (ou
inférieur) approuvé pour l'émetteur par Industrie Can-
ada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il
faut choisir le type d'antenne et son gain de sorte que
la puissance isotrope rayonnée équivalente (p.i.r.e.)
ne dépasse pas l'intensité nécessaire à l'établisse-
ment d'une communication satisfaisante.
ada, le présent émetteur radio peut fonctionner avec
une antenne d'un type et d'un gain maximal (ou
inférieur) approuvé pour l'émetteur par Industrie Can-
ada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il
faut choisir le type d'antenne et son gain de sorte que
la puissance isotrope rayonnée équivalente (p.i.r.e.)
ne dépasse pas l'intensité nécessaire à l'établisse-
ment d'une communication satisfaisante.
The above notice may be affixed to the device instead
of displayed in the user manual.
of displayed in the user manual.
Co ains transmitter module
is device complies wi
ndu
Canada
license-exem
R
andard(s) pera ion is sub-
je to the ollowing two condi ions (1) this device
may not cause interferenc
may not cause interferenc
and (2) this device mu
accept any interference including in
nce h
ay cause undesired operation o the device
Le présen appareil es con orme aux CNR d
dus-
trie Canada applicables aux appareils radio exemp s
de licence L'exploi ation es autorisée aux deux con-
ditions suivant
de licence L'exploi ation es autorisée aux deux con-
ditions suivant
(1) l appareil ne doit pas produire
de brouillage,
(2) l'utilisateur de l appareil doit
accepter out brouillage radioélec rique subi même
si le brouillage es susceptible d'en comprome re le
si le brouillage es susceptible d'en comprome re le
nctionneme