Beat-Sonic Co. Ltd S27870000 사용자 설명서
CHIME-NETIC
User Manual
Dynamo Button
Wireless Chime
Before Installing
System Expansion Options
Installation Instructions
1.Important
a) The Dynamo Button Transmitter is fully water submersible
however the Wireless Receiver is not. Please do not get the
receiver unit wet.
b) Do not disassemble, repair or modify.
c) Always use the recommended power supply.
2.Attention
3.Pack Contents
Dynamo Button Transmitter x 1
Wireless Receiver x 1
Power Adapter x 1
User Manual x 1
Call Label Sheet x 1
B.Suspend the Dynamo Button Transmitter using
hook or lanyard
A. Installing Dynamo Button Transmitter using
double-sided tape
2.Melody Selection
1. Two Buttons & One Receiver
a) Avoid installing the Dynamo Button Transmitter on or directly
near metal surfaces as this will reduce the operating range.
b) When locating the Dynamo Button Transmitter onto a vinyl
coated door or door frame, always check the operating
performance before final installation as the internal metal
frame may affect perfomance.
Program an extra Dynamo Button Transmitter to operate with the
Wireless Receiver. Extra Dynamo Button Transmitter (product code:
CNB2US-1) required.
2. One Button & Two Receivers
Program an extra Wireless Receiver to operate with the Dynamo
Button Transmitter. Extra Wireless Receiver (product code:
CNB2US-2) required.
3. Three Buttons & One Receiver
Program an extra two Dynamo Button Transmitter to operate with the
Wireless Receiver. Up to a total of three (3) Dynamo Button
Transmitters can be programmed to each Wireless Receiver.Two
extra Dynamo Button Transmitters (Product code: CNB2US-1)
required.
4. One Button & Three or More Receivers
Program an extra two or more Wireless Receivers to operate with
each Dynamo Button Transmitter. An unlimited number of Wireless
Receivers can be programmed to operate with each Dynamo Button
Transmitter. Two or more extra Wireless Receivers (product code:
CNB2US-2) required.
5. Two Buttons & Two Receivers
Program an extra Dynamo Button Transmitter and an extra Wireless
Receiver. One extra Dynamo Button Transmitter (product code:
CNB2US-1) and one extra Wireless Receiver (product code:
CNB2US-2) required.
6. Three Buttons & Multiple Receivers
Program up to three Dynamo Button Transmitters per Wireless
Receiver. An unlimited number of Wireless Receivers can be
programmed to operate with each Dynamo Button Transmitter. Extra
Dynamo Button Transmitters (product code: CNB2US-1) and extra
Wireless Receivers (product code: CNB2US-2) required.
1. Connect the Wireless Receiver to a power outlet
using the approved AC power adapter.
2. Press the Dynamo Button Transmitter to confirm the
chime is now operational.
3. Select the desired mounting position for the
Dynamo Button Transmitter making sure it is within
range of the Wireless Receiver. Note that walls and
doors will reduce the effective range.
4. Be sure to avoid mounting the Dynamo Button
Transmitter on metal surfaces as this will greatly
reduce its effective range.
5. Confirm that the chime operates reliably for the
chosen positions then secure using either the
double sided tape or by using a wall hook or screw.
Operating Instructions
1.Normal Operation
The Wireless Receiver and Dynamo Button Transmitter have
been pre-programmed from factory and are ready to use. Simply
install according to the above instructions and the Wireless
Receiver will sound and the indicator light will flash when the
button is pressed.
Peel back one side of the
double-sided tape and attach to the
back of the Dynamo Button
Transmitter.
Check that the surface is clean, dry
and free of any loose material.
Attach the Dynamo Button
Transmitter to the desired position
then press and hold against the
surface for at least 30 seconds.
Insert a self tapping screw or a wall
hook into the marked location.
For personal use, the Dynamo
Button Transmitter can be worn
around the neck using a lanyard
(lanyard not included).
* When using for personal use,
always test first the maximum
operating range.
The Dynamo Button Wireless Chime comes
with 25 selectable ring tones. Press the round
button on the Wireless Receiver to cycle
through and select your choice of melody.
Disconnecting then re-connecting power to
the unit will reset the melody to the default
"Ding-Dong" melody.
3. Volume Control
Press the round button twice quicky to
adjust the chime volume. The Wireless
Receiver has three selectable volume
settings (low, medium, high).
Even greater volume can be achieved by mounting the
Wireless Receiver against a hard surface to reflect the
sound.
Press once to
select melody
Press twice
to adjust
volume
230*326
Please contact Beat-Sonic USA to purchase extra Dynamo Button Transmitters and Wireless Receivers
web: www.beatsonicusa.com email: info@beatsonicusa.com
♬
♬
♬
♬
♬
♬
♬
♬
♬
♬
♬
472-5, Koushin, Fujieda, Nisshin, Aichi, JAPAN.
TEL: +81-561-73-9000 FAX: +81-561-74-5554
www.beatsonic.co.jp E-mail: enquiries@beatsonic.co.jp
TEL: +81-561-73-9000 FAX: +81-561-74-5554
www.beatsonic.co.jp E-mail: enquiries@beatsonic.co.jp
International inquiries.
USA and Canada inquiries.
14778 Beach Blvd. La Mirada, CA 90638
TEL: 1-714-994-1085 FAX: 1-714-249-4741
www.beatsonicusa.com E-mail: info@beatsonicusa.com
TEL: 1-714-994-1085 FAX: 1-714-249-4741
www.beatsonicusa.com E-mail: info@beatsonicusa.com
株式会社 ビートソニック
Beat-Sonic USA Inc.