Troy-Bilt 12235 사용자 설명서
INTRODUCTION
Read these instructions in their entirety
before you attempt to assemble or op-
erate your new equipment.
IMPORTANT: The correct mixture of un-
leaded automotive gasoline and two-cycle
motor oil (a 24:1 ratio of gasoline to two-
cycle oil) must be added to the fuel tank
before starting the engine. See instruc-
tions in this Section.
before you attempt to assemble or op-
erate your new equipment.
IMPORTANT: The correct mixture of un-
leaded automotive gasoline and two-cycle
motor oil (a 24:1 ratio of gasoline to two-
cycle oil) must be added to the fuel tank
before starting the engine. See instruc-
tions in this Section.
UNPACKING INSTRUCTIONS
1. Inspect your machine immediately. If
you find or suspect damage to the carton
or contents, contact your local authorized
dealer or the Factory for assistance.
you find or suspect damage to the carton
or contents, contact your local authorized
dealer or the Factory for assistance.
2. Remove any packing material. Check
for small parts before discarding the
packing material.
for small parts before discarding the
packing material.
3. Loose parts include the following:
(2) Long Bushings
(Packed in a separate plastic bag)
(Packed in a separate plastic bag)
4. Perform the assembly on a clean, level
surface. Be careful not to severely bend
any of the control cables on the unit.
surface. Be careful not to severely bend
any of the control cables on the unit.
5. Before starting any assembly steps,
disconnect the engine spark plug wire
from the spark plug.
disconnect the engine spark plug wire
from the spark plug.
ASSEMBLY STEPS
STEP 1: Unfold and Adjust
Handlebar
Handlebar
IMPORTANT: Be careful not to pinch any
wires or cables while unfolding and ad-
justing the handlebar.
1. Loosen the two handlebar knobs (A,
Figure 1) and unfold the handlebar into
the operating position. Do not use force
— if there is binding, continue to loosen
the knobs.
wires or cables while unfolding and ad-
justing the handlebar.
1. Loosen the two handlebar knobs (A,
Figure 1) and unfold the handlebar into
the operating position. Do not use force
— if there is binding, continue to loosen
the knobs.
2. There are two height settings holes in
the upper handlebar. The unit is shipped
with the handlebar knobs in the lowest
height setting holes. If this height is cor-
rect for you, simply tighten the two han-
dlebar knobs. If a higher setting is de-
sired, reposition the handlebar knobs,
mounting screws and washers in the
other set of holes.
the upper handlebar. The unit is shipped
with the handlebar knobs in the lowest
height setting holes. If this height is cor-
rect for you, simply tighten the two han-
dlebar knobs. If a higher setting is de-
sired, reposition the handlebar knobs,
mounting screws and washers in the
other set of holes.
3. Check the locations of the three plastic
ties (C, Figure 1). The ties must be posi-
tioned as shown.
ties (C, Figure 1). The ties must be posi-
tioned as shown.
NOTE: There is just one handlebar storage
position – folded over the engine as origi-
nally shipped.
position – folded over the engine as origi-
nally shipped.
STEP 2: Inspect and Tighten
Hardware
Hardware
Check all nuts, bolts and screws on your
unit and tighten as needed. NOTE: Use a
7/16" socket with an extension to check
hardware at ends of handlebar.
unit and tighten as needed. NOTE: Use a
7/16" socket with an extension to check
hardware at ends of handlebar.
Tools Needed to Check for Loose
Hardware:
• Adjustable wrench
• Slotted-head screwdriver
• Phillips-head screwdriver
• 7/16" socket and extension
Hardware:
• Adjustable wrench
• Slotted-head screwdriver
• Phillips-head screwdriver
• 7/16" socket and extension
IMPORTANT: Do not tighten engine gov-
ernor screw (D, Figure 2). It is factory-
adjusted for proper engine operation.
ernor screw (D, Figure 2). It is factory-
adjusted for proper engine operation.
STEP 3: Add a Mixture of Gasoline
and Two-Cycle Oil to the Fuel Tank
and Two-Cycle Oil to the Fuel Tank
IMPORTANT: Read the separate Engine
Owner’s Manual before starting the
engine.
1. Use clean, high quality 2-cycle oil,
NMMA TC-WII or TC-W3. DO NOT USE
MULTI-VISCOSITY OIL!
Owner’s Manual before starting the
engine.
1. Use clean, high quality 2-cycle oil,
NMMA TC-WII or TC-W3. DO NOT USE
MULTI-VISCOSITY OIL!
2. Use fresh, clean, unleaded regular,
unleaded premium or reformulated au-
tomotive gasoline only. DO NOT USE
LEADED GASOLINE.
unleaded premium or reformulated au-
tomotive gasoline only. DO NOT USE
LEADED GASOLINE.
Assembly
2
Section
Figure 1: Loosen handlebar knobs and
unfold handlebar. Slide plastic ties to the
locations shown.
unfold handlebar. Slide plastic ties to the
locations shown.
A
A
C
B
C
C
Figure 2: Do not adjust or tighten the engine
governor screw.
governor screw.
D
• Gasoline and its vapors are highly
flammable and explosive. Keep gaso-
line away from possible ignition
sources.
line away from possible ignition
sources.
• Do not smoke while mixing the gaso-
line and two-cycle oil together or
when filling the fuel tank.
when filling the fuel tank.
• Never fill fuel tank when engine is run-
ning or hot.
Failure to follow these precautions could
result in the fuel igniting, causing per-
sonal injury or property damage.
result in the fuel igniting, causing per-
sonal injury or property damage.
DANGER
5
To prevent personal injury or property
damage, do not start the engine until all
assembly steps are complete and you
have read and understand the safety and
operating instructions in this manual.
damage, do not start the engine until all
assembly steps are complete and you
have read and understand the safety and
operating instructions in this manual.
WARNING
Contact with rotating tines or other
moving parts can cause serious personal
injury.
moving parts can cause serious personal
injury.
Before installing or removing attach-
ments, or adjusting or servicing the ma-
chine, stop the engine, let all moving
parts come to a complete stop, discon-
nect the spark plug wire and move the
wire away from the spark plug.
ments, or adjusting or servicing the ma-
chine, stop the engine, let all moving
parts come to a complete stop, discon-
nect the spark plug wire and move the
wire away from the spark plug.
WARNING