AMX PS-POE-AT-TC FG423-84 전단
제품 코드
FG423-84
Installation Guide
PS-POE-AT-TC
High-Power 802.3at Compliant PoE Injector
Overview
The PS-POE-AT-TC (FG423-84) is a single port, high-power solution for
remote powering of current and emerging high-power applications. The PS-
POE-AT-TC combines a 802.3at-compliant Power-over-Ethernet (PoE)
power supply with an integral DC Injector (FIG. 1). It provides DC power for
one PoE-equipped device by “injecting” DC power through the CAT5
Ethernet cable.
remote powering of current and emerging high-power applications. The PS-
POE-AT-TC combines a 802.3at-compliant Power-over-Ethernet (PoE)
power supply with an integral DC Injector (FIG. 1). It provides DC power for
one PoE-equipped device by “injecting” DC power through the CAT5
Ethernet cable.
The PS-POE-AT-TC supports the IEEE standard PoE pinout: Pins 4&5
Power (+) / Pins 7&8 Power (-). See Pin Connections (on reverse) for
details.
Power (+) / Pins 7&8 Power (-). See Pin Connections (on reverse) for
details.
Key features include:
•
Power over Ethernet (PoE)
•
IEEE 802.3at compliant with 2-event classification
•
IEEE 802.3af backward-compatible
•
Output power of 30W guaranteed
•
Supports 10/100/1000 Base-T applications
•
Compatible with IEEE 802.3af devices and pre-standard devices
•
Safe for low-power devices: they receive only the power they need
•
Automatic detection and protection of non-standard Ethernet terminals
•
Compact design fits easily in WLAN access point and IP camera
installations
Product Specifications
Safety Information
Important Safety Information
•
The PS-POE-AT-TC should be connected to PoE networks only, without
routing to an outside network.
•
Only qualified personnel can install or remove the PS-POE-AT-TC.
•
AC Power Cord Set:
* The power cord must have regulatory agency approval for the specific
country in which it is used (for example, UL, CSA, VDE, etc.)
country in which it is used (for example, UL, CSA, VDE, etc.)
* The power cord must be a three-conductor type (two current-carrying
conductors and one ground conductor) terminated on one end by an IEC
60320 appliance coupler (for connection to the PS-POE-AT-TC), and on
the other end by a plug containing a ground (earthing) contact.
conductors and one ground conductor) terminated on one end by an IEC
60320 appliance coupler (for connection to the PS-POE-AT-TC), and on
the other end by a plug containing a ground (earthing) contact.
* The power cord must be rated for a minimum of 250 VAC RMS
operation, with a minimum rated current capacity of 5 amps or a minimum
operation, with a minimum rated current capacity of 5 amps or a minimum
wire gauge of 18 AWG (0.75 mm
2
).
•
A PS-POE-AT-TC installed in Australia requires power cords with a
minimum wire gauge of 16 WWG (1.0 mm
2
).
•
The PS-POE-AT-TC DATA IN and DATA & POWER OUT ports are
shielded RJ45 data sockets. They CANNOT be used as Plain Old
Telephone Service (POTS) telephone sockets. Only RJ45 data connectors
may be connected to these sockets.
Telephone Service (POTS) telephone sockets. Only RJ45 data connectors
may be connected to these sockets.
•
The AC wall socket-outlet must be near the PS-POE-AT-TC and easily
accessible. You can remove AC power from the PS-POE-AT-TC by
disconnecting the AC power cord from either the wall socket-outlet or the
PS-POE-AT-TC appliance coupler.
disconnecting the AC power cord from either the wall socket-outlet or the
PS-POE-AT-TC appliance coupler.
FIG. 1
PS-POE-AT-TC Power-Over-Ethernet Power Supply
PS-POE-AT-TC Specifications
Input Specifications
AC Input Voltage Range: 100-240 VAC
AC Input Current:
0.8A @ 100-240 VAC
AC Frequency:
50 to 60 Hz
AC Input Current:
0.8A MAX at 110-240 VAC
Protection:
• Internal Primary Current Fuse
• Inrush Limiting
• Inrush Limiting
Input Power Cord:
Universal Power Cord, 3 Foot
Output Specifications:
Pass Through Data
Rates:
Rates:
10/100/1000 Mbps
Output Voltage:
55 VDC Nominal
Output Power:
30 Watts (Guaranteed)
Output Current:
0.6A (max)
Ripple and Noise:
Below the IEEE802.3af requirements
• f<500Hz: Vp-p 0.5
• 500Hz to 150kKHz: Vp-p 0.2
• 150KHz to 500KHz: Vp-p 0.15
• 500KHz to 1MHz: Vp-p 0.1
• 500Hz to 150kKHz: Vp-p 0.2
• 150KHz to 500KHz: Vp-p 0.15
• 500KHz to 1MHz: Vp-p 0.1
Transient Response:
Meets IEC61000-4-4 (1Kv)
PS-POE-AT-TC Specifications (Cont.)
Output Specifications (Cont.):
Leakage Current:
Up to 3uA
Efficiency:
18.4msec at 90Vac
Hold-Up Time:
83%
General Specifications:
LEDs:
• Yellow (On): power is on and active
• Green (On): A remote terminal is connected
• Green (Blinking): Overload state or short
• Green (On): A remote terminal is connected
• Green (Blinking): Overload state or short
circuit
Weight:
0.44 lbs (200 g)
Dimensions (HWD):
5.5" x 2.09” x 1.28" (14 cm x 5.3 cm x 3.25 cm)
Enclosure:
Molded black matte plastic
Cord and Connectors:
Dual shielded RJ45 jacks built into the
enclosure, EIA 568A and 568B
enclosure, EIA 568A and 568B
Compliances:
• IEEE 802.3at (PoE)
• RoHS Compliant
• WEEE Compliant
• CE
• FCC Part 15, Class B
• EN 55022 Class B (Emissions)
• EN 55024 (Immunity)
• VCCI (Japan)
• C-Tick
• UL/cUL per IEC 60950-1
• GS Mark per IEC 60950-1
• RoHS Compliant
• WEEE Compliant
• CE
• FCC Part 15, Class B
• EN 55022 Class B (Emissions)
• EN 55024 (Immunity)
• VCCI (Japan)
• C-Tick
• UL/cUL per IEC 60950-1
• GS Mark per IEC 60950-1
Environmental Specifications:
Operating Temp:
• -4°F to 104°F (-20°C to 40°C) @ 30W
• -4°F to 131°F (-20°C to 55°C) @ 22.5W
• -4°F to 131°F (-20°C to 55°C) @ 22.5W
Storage Temp:
-4°F to +158°F (-20°C to +70°C)
Relative Humidity:
Maximum 90%, Non-Condensing
Thermal Rating:
20 BTU/Hr(@240VAC)
Operating Altitude:
-1000 to 10,000 ft. (-304.8 to 3048 m)