AMX PS-POE-AT-TC FG423-84 Folheto

Installation Guide

PS-POE-AT-TC

 

High-Power 802.3at Compliant PoE Injector

Overview

The PS-POE-AT-TC (FG423-84) is a single port, high-power solution for 
remote powering of current and emerging high-power applications. The PS-
POE-AT-TC combines a 802.3at-compliant Power-over-Ethernet (PoE) 
power supply with an integral DC Injector (FIG. 1). It provides DC power for 
one PoE-equipped device by “injecting” DC power through the CAT5 
Ethernet cable. 

The PS-POE-AT-TC supports the IEEE standard PoE pinout: Pins 4&5 
Power (+) / Pins 7&8 Power (-). See Pin Connections (on reverse) for 
details. 

Key features include:

•

Power over Ethernet (PoE)

•

IEEE 802.3at compliant with 2-event classification

•

IEEE 802.3af backward-compatible

•

Output power of 30W guaranteed

•

Supports 10/100/1000 Base-T applications

•

Compatible with IEEE 802.3af devices and pre-standard devices

•

Safe for low-power devices: they receive only the power they need

•

Automatic detection and protection of non-standard Ethernet terminals

•

Compact design fits easily in WLAN access point and IP camera 

installations

Product Specifications 

Safety Information

Important Safety Information

•

The PS-POE-AT-TC should be connected to PoE networks only, without 

routing to an outside network.

•

Only qualified personnel can install or remove the PS-POE-AT-TC.

•

AC Power Cord Set:

* The power cord must have regulatory agency approval for the specific 
country in which it is used (for example, UL, CSA, VDE, etc.)

* The power cord must be a three-conductor type (two current-carrying 
conductors and one ground conductor) terminated on one end by an IEC 
60320 appliance coupler (for connection to the PS-POE-AT-TC), and on 
the other end by a plug containing a ground (earthing) contact.

* The power cord must be rated for a minimum of 250 VAC RMS 
operation, with a minimum rated current capacity of 5 amps or a minimum 

wire gauge of 18 AWG (0.75 mm

2

).

•

A PS-POE-AT-TC installed in Australia requires power cords with a 

minimum wire gauge of 16 WWG (1.0 mm

2

).

•

The PS-POE-AT-TC DATA IN and DATA & POWER OUT ports are 

shielded RJ45 data sockets. They CANNOT be used as Plain Old 
Telephone Service (POTS) telephone sockets. Only RJ45 data connectors 
may be connected to these sockets.

•

The AC wall socket-outlet must be near the PS-POE-AT-TC and easily 

accessible. You can remove AC power from the PS-POE-AT-TC by 
disconnecting the AC power cord from either the wall socket-outlet or the 
PS-POE-AT-TC appliance coupler.

PS-POE-AT-TC Power-Over-Ethernet Power Supply

PS-POE-AT-TC Specifications

AC Input Voltage Range: 100-240 VAC

AC Input Current:

0.8A @ 100-240 VAC

AC Frequency:

50 to 60 Hz

AC Input Current:

0.8A MAX at 110-240 VAC

Protection:

• Internal Primary Current Fuse
• Inrush Limiting

Input Power Cord:

Universal Power Cord, 3 Foot

Pass Through Data 
Rates:

10/100/1000 Mbps

Output Voltage:

55 VDC Nominal

Output Power:

30 Watts (Guaranteed)

Output Current:

0.6A (max)

Ripple and Noise:

Below the IEEE802.3af requirements

• f<500Hz: Vp-p 0.5
• 500Hz to 150kKHz: Vp-p 0.2
• 150KHz to 500KHz: Vp-p 0.15
• 500KHz to 1MHz: Vp-p 0.1

Transient Response:

Meets IEC61000-4-4 (1Kv)

PS-POE-AT-TC Specifications (Cont.)

Leakage Current:

Up to 3uA

Efficiency:

18.4msec at 90Vac

Hold-Up Time:

83%

LEDs:

• Yellow (On): power is on and active
• Green (On): A remote terminal is connected
• Green (Blinking): Overload state or short 

circuit

Weight:

0.44 lbs (200 g)

Dimensions (HWD):

5.5" x 2.09” x 1.28" (14 cm x 5.3 cm x 3.25 cm)

Enclosure:

Molded black matte plastic

Cord and Connectors:

Dual shielded RJ45 jacks built into the 
enclosure, EIA 568A and 568B

Compliances:

• IEEE 802.3at (PoE)
• RoHS Compliant
• WEEE Compliant
• CE
• FCC Part 15, Class B
• EN 55022 Class B (Emissions)
• EN 55024 (Immunity)
• VCCI (Japan)
• C-Tick
• UL/cUL per IEC 60950-1
• GS Mark per IEC 60950-1

Operating Temp:

• -4°F to 104°F (-20°C to 40°C) @ 30W
• -4°F to 131°F (-20°C to 55°C) @ 22.5W

Storage Temp:

-4°F to +158°F (-20°C to +70°C)

Relative Humidity:

Maximum 90%, Non-Condensing

Thermal Rating:

20 BTU/Hr(@240VAC)

Operating Altitude:

-1000 to 10,000 ft. (-304.8 to 3048 m)