Intel Xeon 5130 2.0GHz 124716 데이터 시트
제품 코드
124716
Electrical Specifications
30
Dual-Core Intel
®
Xeon
®
Processor 5100 Series Datasheet
Notes:
1.
Unless otherwise noted, all specifications in this table apply to all processors and are based on estimates
and simulations, not empirical data. These specifications will be updated with characterized data from
silicon measurements at a later date.
2.
These voltages are targets only. A variable voltage source should exist on systems in the event that a
different voltage is required. See
for more information.
3.
The voltage specification requirements are measured across the VCC_DIE_SENSE and VSS_DIE_SENSE
lands and across the VCC_DIE_SENSE2 and VSS_DIE_SENSE2 lands with an oscilloscope set to 100 MHz
bandwidth, 1.5 pF maximum probe capacitance, and 1 MΩ minimum impedance. The maximum length of
ground wire on the probe should be less than 5 mm. Ensure external noise from the system is not coupled
in the scope probe.
4.
The processor must not be subjected to any static V
CC
level that exceeds the V
CC_MAX
associated with any
particular current. Failure to adhere to this specification can shorten processor lifetime.
5.
I
CC_MAX
specification is based on maximum V
CC
loadline The processor is capable of drawing I
CC_MAX
for up
to 10 ms.
6.
I
CC_RESET
is specified while PWRGOOD and RESET# are asserted.
7.
This specification represents the total current for GTLREF_DATA and GTLREF_ADD.
8.
V
TT
must be provided via a separate voltage source and must not be connected to V
CC
. This specification is
measured at the land.
9.
Minimum VCC and maximum ICC are specified at the maximum processor case temperature (TCASE)
shown in
.
10. This specification refers to the total reduction of the load line due to VID transitions below the specified
VID.
11. Individual processor VID values may be calibrated during manufacturing such that two devices at the same
frequency may have different VID settings.
12. This specification applies to the VCCPLL land.
13. Baseboard bandwidth is limited to 20 MHz.
I
TT
I
CC
for V
TT
supply before V
CC
stable
I
I
CC
for V
TT
supply after V
CC
stable
4.5
4.6
A
16
I
CC_TDC
Thermal Design Current
(TDC) Dual-Core Intel®
Xeon® Processor LV 5148/
5138/5128
35
A
6,15
I
CC_TDC
Thermal Design Current
(TDC) Dual-Core Intel
®
Xeon
®
Processor 5100
Series
60
A
6,15
I
CC_TDC
Thermal Design Current
(TDC) Dual-Core Intel®
Xeon® Processor 5160
70
A
6,15
I
CC_VTT_OUT
DC current that may be
drawn from V
TT_OUT
per land
580
mA
17
I
CC_GTLREF
I
CC
for
GTLREF_DATA and
GTLREF_ADD
200
µA
8
I
CC_VCCPLL
I
CC
for PLL supply
130
mA
13
I
TCC
I
CC
for Dual-Core Intel®
Xeon® Processor LV 5148/
5138/5128 during active
thermal control circuit (TCC)
45
A
I
TCC
I
CC
for Dual-Core Intel
®
Xeon
®
Processor 5100
Series during active thermal
control circuit (TCC)
65
A
I
TCC
I
CC
for Dual-Core Intel®
Xeon® Processor 5160
during active thermal control
circuit (TCC)
90
A
Table 2-13. Voltage and Current Specifications (Sheet 2 of 2)
Symbol
Parameter
Min
Typ
Max
Unit
Notes
1,13