United States Stove 5040 사용자 설명서

12

OPERATION

THIS STOVE IS APPROVED FOR BURNING PELLETIZED WOOD FUEL ONLY! Factory-approved pellets are those ¼” or 5/16” in diameter and not 

over 1” long. Longer or thicker pellets sometimes bridge the auger flights, which prevents proper pellet feed. Burning wood in forms other than pellets is 

not permitted. It will violate the building codes for which the stove has been approved and will void all warranties. The design incorporates automatic feed 

of the pellet fuel into the fire at a carefully prescribed rate. Any additional fuel introduced by hand will not increase heat output but may seriously impair the 

stoves performance by generating considerable smoke. Do not burn wet pellets. The stove’s performance depends heavily on the quality of your pellet fuel. 

Avoid pellet brands that display these characteristics:

a.  Excess Fines – “Fines” is a term describing crushed pellets or loose material that looks like sawdust or sand. Pellets can be screened before being 

placed in hopper to remove most fines.

b.  Binders – Some pellets are produced with materials to hold them together, or “bind” them.

c.  High ash content – Poor quality pellets will often create smoke and dirty glass. They will create a need for more frequent maintenance. You will have 

to empty the burnpot plus vacuum the entire system more often. Poor quality pellets could damage the auger. US Stove cannot accept responsibility 

for damage due to poor quality pellets. Your dealer can recommend a good quality pellet dealer in your area.

Remove burnpot, making sure it is clean and none of the air holes are plugged. Clean the firebox, and then reinstall burnpot. Clean door glass if neces-

sary (a dry cloth or paper towel is usually sufficient). Never use abrasive cleaners on the glass or door. Check fuel in the hopper, and refill if necessary.

NOTE: The Hopper can hold up to 45 lbs. of pellets.

Never use a grate or other means of supporting the fuel. Use only the US Stove approved burnpot.

During the start up period:

1) DO NOT open the viewing door.

2) DO NOT open the damper more than ¼”.

3) DO NOT add pellets to the burnpot by hand.

4) DO NOT use the Fuel Feed button (unless you are priming the auger after running out of pellets).

A dangerous condition could result.

NOTE: During the first few fires, your stove will emit an odor as the high temperature paint cures or becomes seasoned to the metal. Maintaining smaller 

fires will minimize this. Avoid placing items on stovetop during this period because paint could be affected.

a.  Fill hopper and clean burnpot.

b.  Press “Power” button. Make sure light is on.

c.  The damper should be completely closed or open no more than ¼” during start-up. This will vary depending on your installation and elevation. Once 

fire is established adjust for desired flame increasing the amount the damper is open as the heat setting is increased.

 (See

“DAMPER CONTROL”)

d.  Adjust feed rate to desired setting by pressing “Feed Rate Advance” button.

If fire doesn’t start in 15 minutes, press “Power”, wait a few minutes and start procedure again.

The damper control rod on the stove’s lower left side adjusts the combustion air. This control is necessary due to the varied burn characteristics of individual 

installations, different pellet brands and pellet feed rates. It allows you to improve the efficiency of your stove. Providing correct combustion air will reduce 

the frequency of cleaning your glass door and prevent the rapid buildup of creosote inside your stove and chimney.

You should adjust the damper based on the fire’s appearance. A low, reddish, dirty fire can be improved by pulling the damper out slightly. A “blow torch” 

fire can be improved by pushing the damper in a bit.

As a general rule, on lower feed rate settings, the damper should be in farther. On higher feed rates, the damper should be more open. Through trial and 

error, you will find the best setting. Consult your dealer if you need help.

NOTE: On “1”, damper should be either completely closed or out approximately ⅛” to ¼”. If damper is out too far, it can cause the fire to go out.

If the door is opened while the stove is in operation it must be closed within 30 seconds or the stove will shut down. If the stove shuts down push the “Power” 

button to continue the operation of your stove.

When starting your stove the Room Air Fan will not come on until the stove’s heat exchanger warms up. This usually takes about 10 minutes from 

startup.