Siemens TRAFFIC CONTROLS TC12 사용자 설명서
TC12 Installation, Commissioning & Maintenance Handbook
normal direction loop connects (the reverse direction loop is
.
onding to
ver the handset
ts.
ommands CUD and UDT. Note: These functions only work if they are enabled in
3.3.3.13 Reply bit function (GRL)
omm nt:
or ea
bit in this reply byte.
ch reply
byte. The {function} field defines the source that sets the bit, or in
the case of SCOOT loops a group of four bits.
the case of SCOOT loops a group of four bits.
The various functions are as follows:
0 =
For GRL command, this indicates that the reply bit is driven directly.
For GOL command, this indicates that the output bit is driven directly
from the corresponding UTC control bit.
For GOL command, this indicates that the output bit is driven directly
from the corresponding UTC control bit.
1 = Red Lamp Monitor group 0 - first red fail (RL1)
2 = Red Lamp Monitor group 0 - second red fail (RL2)
3 = Red Lamp Monitor group 0 - any lamp fail (LF)
4 = Red Lamp Monitor group 1 - first red fail
5 = Red Lamp Monitor group 1 - second red fail
6 = Red Lamp Monitor group 1 - any lamp fail
7 = Red Lamp Monitor group 2 - first red fail
8 = Red Lamp Monitor group 2 - second red fail
9 = Red Lamp Monitor group 2 - any lamp fail
2 = Red Lamp Monitor group 0 - second red fail (RL2)
3 = Red Lamp Monitor group 0 - any lamp fail (LF)
4 = Red Lamp Monitor group 1 - first red fail
5 = Red Lamp Monitor group 1 - second red fail
6 = Red Lamp Monitor group 1 - any lamp fail
7 = Red Lamp Monitor group 2 - first red fail
8 = Red Lamp Monitor group 2 - second red fail
9 = Red Lamp Monitor group 2 - any lamp fail
10 = Red Lamp Monitor group 3 - first red fail
11 = Red Lamp Monitor group 3 - second red fail
12 = Red Lamp Monitor group 3 - any lamp fail
11 = Red Lamp Monitor group 3 - second red fail
12 = Red Lamp Monitor group 3 - any lamp fail
33 = Red Lamp Monitor group 4 - first red fail
34 = Red Lamp Monitor group 4 - second red fail
35 = Red Lamp Monitor group 4 - any lamp fail
36 = Red Lamp Monitor group 5 - first red fail
37 = Red Lamp Monitor group 5 - second red fail
38 = Red Lamp Monitor group 5 - any lamp fail
39 = Red Lamp Monitor group 6 - first red fail
40 = Red Lamp Monitor group 6 - second red fail
41 = Red Lamp Monitor group 6 - any lamp fail
42 = Red Lamp Monitor group 7 - first red fail
43 = Red Lamp Monitor group 7 - second red fail
44 = Red Lamp Monitor group 7 - any lamp fail
34 = Red Lamp Monitor group 4 - second red fail
35 = Red Lamp Monitor group 4 - any lamp fail
36 = Red Lamp Monitor group 5 - first red fail
37 = Red Lamp Monitor group 5 - second red fail
38 = Red Lamp Monitor group 5 - any lamp fail
39 = Red Lamp Monitor group 6 - first red fail
40 = Red Lamp Monitor group 6 - second red fail
41 = Red Lamp Monitor group 6 - any lamp fail
42 = Red Lamp Monitor group 7 - first red fail
43 = Red Lamp Monitor group 7 - second red fail
44 = Red Lamp Monitor group 7 - any lamp fail
connected to the next input after the normal direction loop)
Note. The 32 inputs are numbered 1 to 32 in section 3.2.3.5, corresp
the associated pin on the 40 way input connector, howe
command numbers the inputs from 0 to 31, for the 32 inpu
command numbers the inputs from 0 to 31, for the 32 inpu
The controller provides U/D for an Integral OTU. See the Controller Handset
C
the T400’s configuration.
GRL{Reply byte no.: 0 to 13} {bit no.: 0 to 7}={function: 0 to 255} (0)
C
e
F
ch reply byte set up the function of each
This command is therefore repeated up to eight times for ea
666/HE/43100/000
Page 91
Issue 9