Sears Cordless Drill 315.11485 사용자 설명서

11

Do not allow familiarity with tools make 

you careless. Remember that a careless fraction of a 
second is sufficient to inflict severe injury.

The battery pack for your tool has been shipped in a low 
charge condition to prevent possible problems. Therefore, 
you should charge it until light on front of charger changes 
from red to green.
Note: Batteries will not reach full charge the first time they 
are charged. Allow several cycles (drilling followed by 
recharging) for them to become fully charged.

See Figure 1.
n

   Charge battery pack only with the charger provided.

n

   Make sure power supply is normal household voltage, 

120 volts, 60 Hz, AC only.

n

   Connect charger to power supply.

n

    Place battery pack in charger aligning raised rib on 

battery pack with groove in charger. See Figure 1.

n

   Press down on battery pack to be sure contacts on 

battery pack engage properly with contacts in charger.

n 

Normally, the red LED on charger will come on. This 

indicates charger is in fast charging mode.

n 

Red LED

 should remain on for approximately 1 hour 

then the green LED will come on. Green LED on indi-
cates battery pack is fully charged and charger is in 
trickle charge mode. Note: Green LED will remain on 
until battery pack is removed from charger or charger 
is disconnected from power supply.

n 

If both yellow and green LED come on, this indicates a 

deeply discharged or defective battery pack.

n

   Allow battery pack to remain in charger for 15 to 30 

minutes. When battery pack reaches normal voltage 
range, red LED should come on. 

n

   If red LED does not come on after 30 minutes, this 

indicates a defective battery pack and should be 
replaced.

n

   After normal usage, a minimum of 1 hour of charging 

time is required to fully recharge battery pack. 

n

    The battery pack will become slightly warm to the 

touch while charging. This is normal and does not 
indicate a problem.

n

    Do not place charger and battery pack in an area of 

extreme heat or cold. It will work best at normal room 
temperature.

  

Note: Charger and battery pack should be placed in a 

location where the temperature is more than 50°F but 
less than 100°F.

n

When batteries become fully charged, unplug charger 
from power supply and remove the battery pack.

n

   Red LED on = Fast charging mode.

n

   Green LED on = Fully charged and in trickle charge 

mode.

n

   Green LED on = When battery pack is inserted into 

charger, indicates hot battery pack or that battery 
pack is out of or below normal temperature range.

n

   Yellow and Green LEDs on = Deeply discharged or 

defective battery pack.

n

   No LED on = Defective charger or battery pack.

To prevent damage to battery pack, 

remove battery pack from charger immediately if no 
LED comes on. Return battery pack and charger to 
your nearest Sears Service Center for checking or 
replacing. Also, if you are removing battery pack from 
charger and no LEDs are on, return both battery pack 
and charger to your nearest Sears Service Center. 
Do not insert another battery pack into charger. A 
damaged charger may damage a battery pack.  

When using your drill-driver continuously, the batteries in 
your battery pack will become hot. You should let a hot 
battery pack cool down for approximately 30 minutes 
before attempting to recharge. When the battery pack 
becomes discharged and is hot, this will cause the green 
LED to come on instead of the red LED. After 30 minutes, 
reinsert battery pack in charger. If green LED continues 
to remain on, return battery pack to your nearest Sears 
Repair Center for checking or replacing.
Note: This situation only occurs when continuous use of 
your drill causes the batteries to become hot. It does not 
occur under normal circumstances. Refer to "CHARGING 
BATTERY PACK" for normal recharging of batteries. If the 
charger does not charge your battery pack under normal 
circumstances, return both the battery pack and charger 
to your nearest Sears Repair Center for electrical check.

If battery pack is below normal temperature range, the 
green LED on charger will come on. Allow battery pack to 
reach normal temperature, then the red LED will come on.
Note: Refer to "CHARGING BATTERY PACK" for normal 
recharging of batteries. If the charger does not charge 
your battery pack under normal circumstances, return 
both the battery pack and charger to your nearest Sears 
Repair Center for electrical check.