Parker Hannifin 6K 사용자 설명서

; IP address 172.54.125.34

2NTCONN1

; Attempt connection to network server #2

2NTMPRB3,15,15,35

; File 3, elements 15-29, in the AB PLC are mapped to
; the 6K's binary variables VARB35-VARB49

2NTPOLL50

; Start polling network server #2, set interval to 50 ms

WAIT(VARB40=b1111111100000000)

; Wait until the value of VARB40 (mapped to file 3,
; element 20, in the PLC) is 1111111100000000

NTMPWB

Network Map Binary Variables for Writing to PLC

Type:

Network

Product Rev

Syntax:

<!><n>NTMPWB,,,

Units:

n = network server #
1

i = Allen Bradley data file #

i = # of the 1

element in data file (beginning of range)

i = # of the elements to include in range

i = # of the 1

binary (VARB) variable in the 6K to map to

Range:

n = 1-6
1

i = 0-n (n depends on size of file)

i = 0 or 1-50 (0 disables polling for this mapping only)

i = 1-125

Default:

1NTMPWB0,0,0,0 (no mapping)

Response:

1NTMPWB: *1NTMPWB1,5,15,23

See Also:

NTCONN, NTIP, NTMPRB, NTMPWI, NTMPRI, NTPOLL, [ NTS ], TNTS,
TNTSF, VARB

6K 5.3

<n>

NTMPWB

,,,

Network Server #

Range: 1-6

# of Allen-Bradley data file

# of first element in AB data file
(beginning of range)

# of elements in range

# of first binary variable (VARB) in 6K

(beginning of range, max value is 125)

EXAMPLE:

IF:

• Allen-Bradley PLC is server #2

• In the PLC’s binary data file 3, use

data elements 0-14 (15 elements
total) for binary data that is to be
transmitted from the 6K.

• Use the 6K’s binary variables 20-34

(15 variables total) to store the data
to be transmitted to the PLC.

The required mapping command is:

2NTMPWB3,0,15,20

The

NTMPWB

command maps a range of binary data elements from the AB PLC to a range of binary (

VARB

) variables in the

6K. There are 125

VARB

variables available in the 6K for exchanging binary data. To perform a binary write to the PLC:

1. Assign the AB PLC a server number, according to its IP address (

NTIP

command).

2. Connect to the AB PLC, according to its server number (

NTCONN

command).

3. Map a range of binary elements in the AB PLC to a range of binary (

VARB

) variables in the 6K (

NTMPWB

command).

4. Start polling the AB device at a specific polling interval (

NTPOLL

command). This updates binary data elements in

the AB PLC with the data from the mapped

VARB

variables in the 6K.

Saved in Non-Volatile Memory

This command is saved in the controller’s non-volatile memory, and is remembered on power-up
and RESET.

Potential Error Conditions:

• You are not allowed to map the same 6K

VARB

variables for read and write functions. Nor are you allowed to map

the same 6K

VARB

variables to another PLC. If you attempt either of these conditions, the 6K will not accept the

NTMPWB

command and will transmit the error message “

VARIABLE MAPPING CONFLICT…

”.

• If you attempt to write to an AB data file of the wrong type, or to a non-existent data element, the 6K will not

accept the

NTMPWB

command, it will transmit the error message “

ERROR, INVALID FILE TYPE, NUMBER OR

SIZE…

” and it will automatically stop polling all mapped binary and integer variables (equivalent to executing the

NTMPRBi,i,0,i

NTMPWBi,i,0,i

NTMPRIi,i,0,i

, and

NTMPWIi,i,0,i

, commands).

page 23