Trac Door model 988 & 988WL 사용자 설명서
©2005 TRAC-RITE DOOR, INC.
Figure 10.
Page 6
KEEPER
1
4
"
CARRIAGE BOLT & NUT
BOTTOM OF
DOOR CURTAIN
DOOR GUIDE
HAND BENT GUIDE TAB
DOOR STOP
5
16
"
CARRIAGE BOLT & NUT
DOOR BRACKET
WA
LL
Figure 8.
Figure 9.
After completeing Step 9, confirm the door is
operating as it should prior to installing any
remaining doors. This will reduce the risk of multiple
installation errors.
NOTE!
10.3 Tighten all 3/8 -16 x 1” wizlock bolts that were loosened
in 10.1.
in 10.1.
11. INTERIOR LOCK INSTALLATION:
11.1 Position door at waist level.
11.1 Position door at waist level.
11.2 Assemble components as shown in Figure 10, noting
that two (2) high collar lock washers are placed over each 1/
4" one-way screw to allow the lockbar to slide freely.
that two (2) high collar lock washers are placed over each 1/
4" one-way screw to allow the lockbar to slide freely.
11.3 As the 1/4" screws are being tightened, move the lockbar
to assure that the high collar lock washers are inside the slots
in the lockbar.
to assure that the high collar lock washers are inside the slots
in the lockbar.
11.4 Mount the lock strike to the bottom of each guide, as
shown, with two (2) 1/4” carriage bolts and jamb nuts through
the pre-punched holes.
shown, with two (2) 1/4” carriage bolts and jamb nuts through
the pre-punched holes.
header while also allowing it to rotate freely. Each end of the
door should be equal distance from the header. The curtain
must be centered in the opening.
door should be equal distance from the header. The curtain
must be centered in the opening.
9. GUIDE ADJUSTMENT:
9.1 With the door approximately 6" from the floor, adjust the
guides so if you grab the door by its bottom assembly, you
shall be able to move it laterally approximately 1/4". Once the
guides are adjusted properly, install the remaining fasteners
and firmly tighten them.
9.1 With the door approximately 6" from the floor, adjust the
guides so if you grab the door by its bottom assembly, you
shall be able to move it laterally approximately 1/4". Once the
guides are adjusted properly, install the remaining fasteners
and firmly tighten them.
9.2 Attach guide warning label (shown in Figure 9) to the
guide at eye level.
guide at eye level.
9.3 Attach tension adjustment warning label (shown in Figure
9) either on the door bracket with the tensioner or to wall at
eye level.
9) either on the door bracket with the tensioner or to wall at
eye level.
10. FINAL POSITIONING:
10.1 With the door in the fully open position, loosen all 3/8-16
x 1” wizlock bolts that connect the axle saddles to the door
bracket.
10.1 With the door in the fully open position, loosen all 3/8-16
x 1” wizlock bolts that connect the axle saddles to the door
bracket.
10.2 Push the door assembly as close as possible toward the
8.3 Attach the two keepers to the bottom interior edge of the
door with one (1) 1/4" carriage bolt and whiz nut in each keeper.
(Figure 8)
door with one (1) 1/4" carriage bolt and whiz nut in each keeper.
(Figure 8)
8.4 Tighten door stops installed in paragraph 8.1 making
certain track bolts are seated in guides. (Figure 8)
certain track bolts are seated in guides. (Figure 8)