Fill-rite Water Pump FR405 사용자 설명서

2

•1" polypropylene ball valve/nozzle
•Buna-N or EPDM hose
•Telescoping steel suction tube
• 820 electronic digital meter (for thin or thick

viscosities)

•2" NPT or 2" buttress inlet bung adapter
•1" FNPT straight and 90

o

 inlet/outlet fittings available

•Wraparound tubular mounting frame
•Santoprene diaphragms
•12 VDC, 24 VDC, 115 VAC/60 Hz, 230 VAC/50 Hz

available

•1" FNPT straight inlet and 90

o

 outlet standard

•15 PSIG maximum outlet pressure
•2600 RPM, 1/4 HP motor:

•12 VDC, rated at 20 amps
•24 VDC, rated at 10amps
•115 VAC/60 Hz rated at 2.0 amps
•230 VAC/50 Hz rated at 1.1 amps

•Thermal overload protection of the motor
•Positive displacement/self-priming design
•Unaffected by particulate materials up to 0.100"

diameter in the pumped fluids

•Flow easily controlled by outlet throttling from

maximum to zero

•Pump may run dry without damage
•Handles viscosities from 1.0 CPS to 3000 CPS

(SAE 140 gear oil at 68

o

F)

•Minimum shear (agitation) of pumped fluids
•Does not include inlet strainer
•Minimum operating temperature: -10ºF  (-23ºC)
•Maximum operating temperature: 130ºF  (54ºC)
•Overall dimensions: 14" (35.6 cm) long x 8.25" (21cm)

high x 8.75" (22.2 cm) deep

•30 minute duty cycle, not for continuous operation

The FR400 Series pump is compatible with the following fluids:

•

Ethylene Glycol, Hydraulic Oil,  Motor Oil, Water

The FR400 Series pump is NOT

NOT

NOT

NOT

NOT compatible with the following

fluids:

•

Acetone, Ammonia, Gasoline, Bleach, Chlorine, Hydro-
chloric Acid, Ink, MEK

If in doubt about compatibility of a specific fluid, contact the
supplier of the fluid to check for any adverse reactions to the
wetted materials shown in the parts list.

1. Use Teflon® tape to seal all joints to avoid leakage

of fluids being pumped.  Leaking of caustic and/or hazardous

fluids could result in severe injuries.

2. Never disassemble YOKE ASSEMBLY (see item 12).

3. Tank or barrel should be anchored to prevent tipping in

both the full and empty conditions.

4. The pump motor is equipped with thermal overload pro-

tection. If overheated, it will shut itself off without any

damage to the windings. Be sure to turn off the pump

power if this occurs. As the motor cools, it will start without

warning if power is on.

EXPLOSION PROOF MOTOR

OPTION:  Electrical wiring

should be done by a licensed

electrician in accordance

with approved electrical

codes. Motor should be prop-

erly grounded and a rigid con-

duit should be used when in-

stalling electrical wiring. Im-

proper use or installation of

this product can cause seri-

ous bodily injury or death.

Not for use with fluids that

Not for use with fluids that

Not for use with fluids that

Not for use with fluids that

Not for use with fluids that

have a flash point below 100°F

have a flash point below 100°F

have a flash point below 100°F

have a flash point below 100°F

have a flash point below 100°F

(37.8°C, ie: gasoline, alcohol).

(37.8°C, ie: gasoline, alcohol).

(37.8°C, ie: gasoline, alcohol).

(37.8°C, ie: gasoline, alcohol).

(37.8°C, ie: gasoline, alcohol).

Refer to NFPA 325M (Fire

Refer to NFPA 325M (Fire

Refer to NFPA 325M (Fire

Refer to NFPA 325M (Fire

Refer to NFPA 325M (Fire

Hazard Properties of Flam-

Hazard Properties of Flam-

Hazard Properties of Flam-

Hazard Properties of Flam-

Hazard Properties of Flam-

mable Liquids, Gases, and

mable Liquids, Gases, and

mable Liquids, Gases, and

mable Liquids, Gases, and

mable Liquids, Gases, and

Volatile Solids) for flash

Volatile Solids) for flash

Volatile Solids) for flash

Volatile Solids) for flash

Volatile Solids) for flash

points of common liquids.

points of common liquids.

points of common liquids.

points of common liquids.

points of common liquids.

Static electricity buildup and

Static electricity buildup and

Static electricity buildup and

Static electricity buildup and

Static electricity buildup and

discharge could result in arc

discharge could result in arc

discharge could result in arc

discharge could result in arc

discharge could result in arc

and explosion.

and explosion.

and explosion.

and explosion.

and explosion.

This pump  should not be used to fuel aircraft.  This pump
is not suited for use with fluids for human consumption.

The Fill-Rite Series FR400 is a double action diaphragm pump,
using a patented, spring-driven, positive displacement
mechanism.  The flow rate with low viscosity material  is up to
13 GPM/49 LPM. The ultimate in chemical handling capability
is provided with stainless steel, polypropylene, polyester and
fluorocarbon wetted parts.

 Fluorocarbon

Polypropylene

 FilCon

TM 

                                               Stainless Steel

 Buna-N