Boss Audio Systems GT-100 사용자 설명서

OD-1

This models the sound of the BOSS OD-1 .

OD-2

This is a overdrive sound with high gain .

CRUNCH

This is a crunch sound .

DS-1

This gives a basic, traditional distortion sound .

DS-2

This creates a heavier distortion sound .

METAL1

This is a metal sound with a characteristic 

midrange .

METAL2

This gives a heavy metal sound .

FUZZ

This gives a basic, traditional fuzz sound .

CUSTOM CHAR -50–+50

+: For soloing
-: For backing

-50–+50

This controls the input sound’s low-frequency 

range and adjusts the amount of distortion in the 

low-frequency range

-50–+50

This controls the input sound’s high-frequency 

range and adjusts the amount of distortion in the 

high-frequency range .

CUSTOM LOW -50–+50

Adjusts the low-range tones after distortion is 

applied .

CUSTOM HIGH -50–+50

Adjusts the high-range tones after distortion is 

applied .

COSM technology simulates different preamp characteristics, speaker 

sizes, and cabinet shapes . 

OFF, ON

Turns the COSM AMP effect on/off .

Refer to PREAMP TYPE

0–120

Adjusts the distortion of the amp .

-10–0–+10

Adjusts the sense of compression of the amp .

0–100

Adjusts the volume of the entire preamp .

*  Be careful not to raise the Level setting too 

high .

0–100

Adjusts the tone for the low frequency range .

0–100

Adjusts the tone for the middle frequency range .

0–100

Adjusts the tone for the high frequency range .

0–100

Adjusts the tone for the ultra high frequency 

range .

*  The PRESENCE parameter functions as a 

high-cut filter with some PREAMP TYPEs .

OFF, ON

Turns the bright setting on/off .

*  The BRIGHT parameter setting is available only 

with certain PREAMP TYPEs .

LOW, MIDDLE, 

HIGH

Provides for selection from three levels of 

distortion: LOW, MIDDLE, and HIGH . Distortion 

will successively increase for settings of LOW, 

MIDDLE and HIGH . 

*  The sound of each Type is created on the basis 

that the Gain is set to MIDDLE . So, normally set 

it to MIDDLE .

OFF, ON

SOLO SW is switched on to create the tone to one 

suitable for solos .

0–100

Adjusts the volume level when the SOLO SW is 

ON .

Select the speaker type .

OFF

This turns off the speaker simulator .

ORIGIN 

(ORIGINAL)

This is the built-in speaker of the amp you 

selected with PREAMP TYPE .

1x8"

This is a compact open-back speaker cabinet 

with one 8-inch speaker .

1x10"

This is a compact open-back speaker cabinet 

with one 10-inch speaker .

1x12"

This is a compact open-back speaker cabinet 

with one 12-inch speaker .

2x12"

This is a general open-back speaker cabinet with 

two 12-inch speakers .

4x10"

This is an optimal speaker cabinet for a large 

enclosed amp with four 10-inch speakers .

4x12"

This is an optimal speaker cabinet for a large 

enclosed amp with four 12-inch speakers .

8x12"

This is a double stack of two cabinets, each with 

four 12-inch speakers .

CUSTOM

Custom speaker
You can customize it however you like to match 

the sound you want .

This setting selects the simulated mic type .

DYN57

This is the sound of the SHURE SM-57 . General 

dynamic mic used for instruments and vocals . 

Optimal for use in miking guitar amps .

DYN421

This is the sound of the SENNHEISER MD-421 . 

Dynamic mic with extended low end .

CND451

This is the sound of the AKG C451B . Small 

condenser mic for use with instruments .

CND87

This is the sound of the NEUMANN U87 . 

Condenser mic with flat response .

FLAT

Simulates a mic with perfectly flat response . 

Produces a sonic image close to that of listening 

to the sound directly from the speakers (on site) .

Simulates the distance between the mic and speaker .

OFF MIC

This setting points the mic away from the 

speaker .

ON MIC

Provides conditions whereby the mic is directed 

more towards the speaker .

This simulates the mic position .

CENTER

Simulates the condition that the mic is set in the 

middle of the speaker cone .

1–10 cm

Simulates the condition that the mic is moved 

away from the center of the speaker cone .

MIC LEVEL *1 0–100

Adjusts the volume of the mic .

0–100

Adjusts the volume of the direct sound .

*1 This is enabled when the OUTPUT SELECT parameter is set to LINE/PHONE .