Korg Bicycle PS60 사용자 설명서
Appendices
128
Gate2, Gate2+Dmpr (Gate2, Gate2+Damper)
This is essentially the same as for Gate 1 or Gate 1 + Dmpr.
However when Gate 2 or Gate 2 + Damper are used as a
dynamic modulation source for the EG of 075: St. Env.
Flanger etc. or the AUTOFADE of 076: Stereo Vibrato, a trig‐
ger will occur at each note‐on. (In the case of Gate 1 and
Gate 1 + Dmpr, the trigger occurs only for the first note‐on.)
However when Gate 2 or Gate 2 + Damper are used as a
dynamic modulation source for the EG of 075: St. Env.
Flanger etc. or the AUTOFADE of 076: Stereo Vibrato, a trig‐
ger will occur at each note‐on. (In the case of Gate 1 and
Gate 1 + Dmpr, the trigger occurs only for the first note‐on.)
Exp Vel (Exponential Velocity)
Modulation will be applied exponentially according to the
velocity value. Weak velocity values will produce little
effect, but the effect will increase rapidly as the velocity val‐
ues rise.
velocity value. Weak velocity values will produce little
effect, but the effect will increase rapidly as the velocity val‐
ues rise.
Pedal #04 (Foot Pedal: CC#04)
If you wish to use the assignable foot pedal as a dynamic
modulation source, set DAMPER/PEDAL/SW1 or PEDAL/
SW2 “Pdl” (Globa: Controllers) to FootPedal. ()“Foot Pedal
Assign” on page 129)
A foot controller etc. connected to the DAMPER/PEDAL/
SW1 or PEDAL/SW2 jack can be used to control an effect.
modulation source, set DAMPER/PEDAL/SW1 or PEDAL/
SW2 “Pdl” (Globa: Controllers) to FootPedal. ()“Foot Pedal
Assign” on page 129)
A foot controller etc. connected to the DAMPER/PEDAL/
SW1 or PEDAL/SW2 jack can be used to control an effect.
FootSW #82 (Foot Switch: CC#82)
If you wish to use an assignable foot switch as a dynamic
modulation source, set PEDAL/SW “SW” (Globa/Media:
Controllers) to Foot Switch (CC#82) ()“Foot Switch
Assign” on page 128).
The effect will be controlled when you use a foot switch etc.
connected to the DAMPER/PEDAL/SW1 or PEDAL/SW2
jack.
modulation source, set PEDAL/SW “SW” (Globa/Media:
Controllers) to Foot Switch (CC#82) ()“Foot Switch
Assign” on page 128).
The effect will be controlled when you use a foot switch etc.
connected to the DAMPER/PEDAL/SW1 or PEDAL/SW2
jack.
Tempo
The resulting modulation will be zero at 120 BPM, the maxi‐
mum positive value at 300 BPM, and the maximum negative
value at 40 BPM.
mum positive value at 300 BPM, and the maximum negative
value at 40 BPM.
Foot Switch Assign
Here you can specify the function of an assignable switch
(separately sold PS‐1) connected to the DAMPER/PEDAL/
SW1 or PEDAL/SW2 jacks.
(separately sold PS‐1) connected to the DAMPER/PEDAL/
SW1 or PEDAL/SW2 jacks.
• Set the Global: Controllers ‐ PEDAL/SW “Type” to
Switch, and use the “Foot Switch Function (Sw)”
parameter (page 74) to specify the function.
parameter (page 74) to specify the function.
If you select a function that includes a CC#, that MIDI
control change message will be transmitted each time
the function is turned on/off (Off: 0, On: 127).
control change message will be transmitted each time
the function is turned on/off (Off: 0, On: 127).
List of Foot Switch assignments
Off
This setting disables the switch.
Foot Switch (CC#82)
This lets you use the switch as an AMS or Dmod source.
Note that you’ll also need to assign Foot SW (CC#82) to con‐
trol the desired parameter within the Program or Effect.
Note that you’ll also need to assign Foot SW (CC#82) to con‐
trol the desired parameter within the Program or Effect.
Porta. SW (CC#65)
This controls portamento on/off.
Sostenuto (CC#66)
This controls the sostenuto effect, which holds only the
notes being played at the moment that the footswitch is
turned on.
notes being played at the moment that the footswitch is
turned on.
Soft (CC#67)
Turns the soft pedal effect on and off.
Damper (CC#64)
Turns the damper pedal effect on and off.
Perf Up
Switch operations will select performances. The perfor‐
mance following the performance thatʹs currently selected
will be selected. At the same time, a bank select message
and program change message will be transmitted.
mance following the performance thatʹs currently selected
will be selected. At the same time, a bank select message
and program change message will be transmitted.
Perf Down
Switch operations will select performances. The perfor‐
mance preceding the the current performance will be
selected. At the same time, a bank select message and pro‐
gram change message will be transmitted.
mance preceding the the current performance will be
selected. At the same time, a bank select message and pro‐
gram change message will be transmitted.
Value Inc
Using the foot switch will produce the same function as
pressing the S button.
pressing the S button.
Value Dec
Using the foot switch will produce the same function as
pressing the T button.
pressing the T button.
Tap Tempo
The foot switch will control the system tempo in real‐time.
JS+Y (CC#01)
The switch will control the effect produced by joystick
movement in the +Y direction (Vertical upward).
movement in the +Y direction (Vertical upward).
JS–Y (CC#02)
The switch will control the effect produced by joystick
movement in the –Y direction (Vertical downward).
movement in the –Y direction (Vertical downward).
JS Lock
Switch operations will turn Joystick Lock on/off.
Gate2,Gate2+Dmpr
Gate2
Note
Dmpr
1
2
3
1
2
3
Damper Pedal
Gate2+Dmpr
Time
On
Off
Off