Samsung RF23HSESBSR 사용 및 관리

setting up

 

01

 

SETTING

 UP

3.  Connect the water line installation kit to the 

shut off valve.

Connecting the water supply line to 
the refrigerator.

There are several items that you need to purchase 
to complete this connection. 
You may find these items sold as a kit at your local 
hardware store.

•  ¼” copper tubing
•  ¼” compression nut 

(1pc)

•  Ferrule (2pc)

•  ¼” plastic tubing  

→

 Molded end(Bulb)

•  ¼” compression nut 

(1pc)

Compression 

Nut (1/4”) 

(Assembled) 

Ferrule 

(Not supplied)

Plastic Tubing
(Assembled)
Compression 
Fitting
(Assembled)

Molded 
end(Bulb)

Compression  
nut (B) (1/4”)  
(Not supplied)

or

Copper tubing
(Not supplied)

Plastic tubing (B)
(Not supplied)

Household water supply line

Refrigerator

1.  Connect the household water line to the 

assembled compression fitting.

 

- If you are using copper tubing, slip the 

compression nut ( 

B ) (not supplied) and 

ferrule (not supplied) on the copper tubing (not 

supplied) as shown.

 

- If you are using plastic tubing ( 

B ) , insert the 

molded end (Bulb) of the plastic tubing ( 

B ) 

into the compression fitting.

Do not use without the molded end (Bulb) 

of the plastic tubing ( 

B ).

2.  Tighten the compression nut ( B ) onto the 

compression fitting. 

Do not over-tighten the compression nut ( 

B ) .

3.  Turn the water on and check for any leakage. 

If you find water drops or leakage in the 

connection areas, turn off the main water 

supply. Check the connections and, if 

necessary, tighten.

4.  Flush 1 gallon of water through the filter 

before drinking or using the water from the 

refrigerator. (Flush approximately 6 minutes.) 

To flush, press a large glass or cup against the 

water dispenser lever. Fill the glass, empty it 

into the kitchen sink after it is filled, and then 

repeat.

5.  After you turn on the refrigerator, let the ice 

maker make ice for 1 to 2 days. Over that 

period of time, throw out the first 1 or 2 

buckets of ice the freezer makes to ensure all 

impurities have been removed from the water 

line.

Only connect the water line to a drinkable 

water source.

If you have to repair or disassemble the water line, 

cut off 1/4“ of the plastic tubing to make sure you 

get a snug, leak-free connection.

You can test the water line quickly using a 

paper cup. Under normal conditions, the 

water dispenser can fill a 5.75 oz. (170cc) 

cup in about 10 seconds.

COMPLETING THE SET UP

Now that you have your new refrigerator installed 

in place, you are ready to set up and enjoy the 

features and functions of the appliance.  

By completing the following steps, your refrigerator 

should be fully operational.

1.  Make sure your refrigerator is in an appropriate 

location with reasonable clearance between it 

and the wall. Refer to installation instructions in 

this manual.

2.  Once the refrigerator is plugged in, make sure the 

interior light comes on when you open the doors.

3.  Set the Temperature control to the coldest 

temperature and wait for an hour. The freezer 

will get slightly chilled and the motor will run 

smoothly. Reset the refrigerator and freezer to 

the temperatures you want.

4.  After you plug the refrigerator in, it will take a few 

hours to reach the appropriate temperature. You 

can store food and drinks in the refrigerator after 

the temperature is sufficiently cool.

If condensation or water drops appears on 

both sides of fridge door’s central part, turn the 

Energy Saver mode off after removing it.(See 

the explanation on Energy Saver button in the 

USING THE CONTROL PANEL.)