Bosch d9412gv3 사용자 설명서
D9412GV3/D7412GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters
EN | 82
Bosch Security Systems, Inc. | 10/11 | F01U170807-02
Comm Fail
Default:
0
Selection: 0, 1 to 128 for D9412GV3, 1 to 64
for D7412GV3, A, B, or C
Activates when a control panel cannot communicate
a report after making ten attempts to each routing
destination. At the same time, COMM FAIL RG
displays at the keypad. This relay automatically
resets when a report is sent successfully.
a report after making ten attempts to each routing
destination. At the same time, COMM FAIL RG
displays at the keypad. This relay automatically
resets when a report is sent successfully.
Use this relay to report primary digital
report failure to an alternate
communication device.
report failure to an alternate
communication device.
Log % Full
Default:
0
Selection:
0, 1 to 128 for D9412GV3, 1 to 64
for D7412GV3, A, B, or C
for D7412GV3, A, B, or C
Enter the number of the relay that activates when the
log reaches the programmed percentage of its
capacity as programmed in the Log % Full prompt
under PANEL WIDE PARAMETERS >RPS
Parameters. This relay provides a steady output until
a Get Log and Set Pointer is executed from the
remote programming software (RPS).
log reaches the programmed percentage of its
capacity as programmed in the Log % Full prompt
under PANEL WIDE PARAMETERS >RPS
Parameters. This relay provides a steady output until
a Get Log and Set Pointer is executed from the
remote programming software (RPS).
Summary Fire
Default:
0
Selection:
0, 1 to 128 for D9412GV3, 1 to 64
for D7412GV3, A, B, or C
for D7412GV3, A, B, or C
Enter the number of the relay that activates when any
Fire point in the system (P## Type 0, P## Fire Yes)
enters into alarm. This relay provides a steady output
until all Fire points in the system return to normal.
Refer to Fire Summary Sustain on page 137 for
details on alternate operation.
Fire point in the system (P## Type 0, P## Fire Yes)
enters into alarm. This relay provides a steady output
until all Fire points in the system return to normal.
Refer to Fire Summary Sustain on page 137 for
details on alternate operation.
Summary Alarm
Default:
0
Selection:
0, 1 to 128 for D9412GV3, 1 to 64
for D7412GV3, A, B, or C
for D7412GV3, A, B, or C
Enter the number of the relay that activates when a
Non-fire point enters into alarm. This relay provides a
steady output until the alarm is acknowledged by a
valid passcode, then cleared from alarm memory with
an acknowledgment at the keypad.
Non-fire point enters into alarm. This relay provides a
steady output until the alarm is acknowledged by a
valid passcode, then cleared from alarm memory with
an acknowledgment at the keypad.
This relay does not activate for silent and
invisible alarms.
invisible alarms.
Summary Fire Trouble
Default:
0
Selection:
0, 1 to 128 for D9412GV3, 1 to 64
for D7412GV3, A, B, or C
for D7412GV3, A, B, or C
Activates when any Fire point in the control panel is
in trouble, or if a Fire Supervision point is missing.
This relay provides a steady output until all Fire
points restore to a normal condition.
in trouble, or if a Fire Supervision point is missing.
This relay provides a steady output until all Fire
points restore to a normal condition.
Summary SupFire
Default:
0
Selection:
0, 1 to 128 for D9412GV3, 1 to 64
for D7412GV3, A, B, or C
for D7412GV3, A, B, or C
Activates when any Fire Supervisory point in the
control panel is in a supervisory condition (off-
normal). This relay provides a steady output until all
Fire Supervisory points are restored to a normal
condition.
control panel is in a supervisory condition (off-
normal). This relay provides a steady output until all
Fire Supervisory points are restored to a normal
condition.
Summary Trouble
Default:
0
Selection: 0, 1 to 128 for D9412GV3, 1 to 64
for D7412GV3, A, B, or C
Activates when any Non-fire point in the control panel
is in a trouble condition. This relay provides a steady
output until the user at the keypad acknowledges the
trouble.
is in a trouble condition. This relay provides a steady
output until the user at the keypad acknowledges the
trouble.
Summary SupBurg
Default:
0
Selection: 0, 1 to 128 for D9412GV3, 1 to 64
for D7412GV3, A, B, or C
Activates when any Non-fire Supervisory point in the
control panel is in a supervisory condition, or if a
Supervisory Burg point is missing. This relay provides
a steady output until the user at the keypad
acknowledges the condition.
control panel is in a supervisory condition, or if a
Supervisory Burg point is missing. This relay provides
a steady output until the user at the keypad
acknowledges the condition.
2.1
Passcode or Token Worksheet
These programming items assign:
a passcode to user groups 001 to 249,
areas by authority level, and
a User Group Window.
a passcode to user groups 001 to 249,
areas by authority level, and
a User Group Window.