ATTO Technology 1500D/E 사용자 설명서
5
ATTO Technology Inc. iPBridge Installation and Operation Manual
1.2 ATTO iPBridge 1500D
The ATTO iPBridge 1500D is a 1-Gigabit Ethernet to SCSI embeddable bridge for midrange
performance, cost effective solutions in SMB/SME environments.
performance, cost effective solutions in SMB/SME environments.
The iPBridge 1500E includes a single Ethernet
port which may be used for either data transfer or
configuration, a serial management port and a
SCSI port.
port which may be used for either data transfer or
configuration, a serial management port and a
SCSI port.
Dimensions
Width: 7.5 inches wide
Width: 7.5 inches wide
Depth: 5.0 inches long
Height: 1.76 inches
Environment
Operating Temperature: 0-70° C external
Operating Temperature: 0-70° C external
Ambient air should not exceed 40°C.
Humidity: 10-90% non-condensing
Recommended airflow: 11 cubic feet per minute.
Power
Plug in the 12 volt, 20 Watt wall mount adapter to
the back of the unit, then into an appropriate
power source (100-240 VAC input, 50/60 Hz).
The power source must be connected to a
protective earth ground and comply with local
electrical codes. Improper grounding may result
in an electrical shock or damage to the unit.
Plug in the 12 volt, 20 Watt wall mount adapter to
the back of the unit, then into an appropriate
power source (100-240 VAC input, 50/60 Hz).
The power source must be connected to a
protective earth ground and comply with local
electrical codes. Improper grounding may result
in an electrical shock or damage to the unit.
Input voltage: 12.0V DC +10%
SCSI port
The SCSI port on the iPBridge 1500E connects
storage devices into the Storage Area Network
(SAN). The port is an Ultra 3 LVD/SE SCSI bus
with 68-pin “P” interface: 160 MB/sec. maximum
throughput, downward compatible with all forms
of single-ended SCSI.
The SCSI port on the iPBridge 1500E connects
storage devices into the Storage Area Network
(SAN). The port is an Ultra 3 LVD/SE SCSI bus
with 68-pin “P” interface: 160 MB/sec. maximum
throughput, downward compatible with all forms
of single-ended SCSI.
The iPBridge supports SCSI devices including
hard disk drives, tape drives RAID controllers,
DVD and CD libraries.
hard disk drives, tape drives RAID controllers,
DVD and CD libraries.
Ethernet port
The 10/100/1000 GbE RJ45 Ethernet port uses
the Intel 8254x family gigabit Ethernet
controllers to support Telnet-based data transfer
and management through an ASCII-based
command line interface or ATTO ExpressNAV, a
browser-based interface.
The 10/100/1000 GbE RJ45 Ethernet port uses
the Intel 8254x family gigabit Ethernet
controllers to support Telnet-based data transfer
and management through an ASCII-based
command line interface or ATTO ExpressNAV, a
browser-based interface.
GbE cables must be at least CAT-5E certified for
1000 Mb/sec. use.
1000 Mb/sec. use.
LED indicators
Activity:
A green LED on the top of the iPBridge
blinks to show the unit is ready and to identify the
iPBridge when the CLI command
iPBridge when the CLI command
IdentifyBridge
is
enabled. It goes dark when there is SCSI activity.
SCSI Activity:
the SCSI bus has an LED which is
lit when the iPBridge is ready and goes dark when
there is SCSI activity.
there is SCSI activity.
Reset switch
A manual reset switch is mounted on the board.
Insert a tool in the hole in the back panel to
activate the switch.
A manual reset switch is mounted on the board.
Insert a tool in the hole in the back panel to
activate the switch.
SCSI ID LED