Texas Instruments SM320F2812-HT 사용자 설명서
www.ti.com
SGUS062A – JUNE 2009 – REVISED APRIL 2010
Table 6-5. XCLKIN Timing Requirements – PLL Bypassed or Enabled
(1)
NO.
MIN
MAX
UNIT
C8
t
c(CI)
Cycle time, XCLKIN
6.67
250
ns
Up to 30 MHz
6
C9
t
f(CI)
Fall time, XCLKIN
ns
30 MHz to 150 MHz
2
Up to 30 MHz
6
C10
t
r(CI)
Rise time, XCLKIN
ns
30 MHz to 150 MHz
2
C11
t
w(CIL)
Pulse duration, X1/XCLKIN low as a percentage of t
c(CI)
40
60
%
C12
t
w(CIH)
Pulse duration, X1/XCLKIN high as a percentage of t
c(CI)
40
60
%
(1)
Not production tested.
Table 6-6. XCLKIN Timing Requirements – PLL Disabled
(1)
NO.
MIN
MAX
UNIT
C8
t
c(CI)
Cycle time, XCLKIN
6.67
250
ns
Up to 30 MHz
6
C9
t
f(CI)
Fall time, XCLKIN
ns
30 MHz to 150 MHz
2
Up to 30 MHz
6
C10
t
r(CI)
Rise time, XCLKIN
ns
30 MHz to 150 MHz
2
XCLKIN
≤
120 MHz
40
60
C11
t
w(CIL)
Pulse duration, X1/XCLKIN low as a percentage of t
c(CI)
%
120 < XCLKIN
≤
150 MHz
45
55
XCLKIN
≤
120 MHz
40
60
Pulse duration, X1/XCLKIN high as a percentage of
C12
t
w(CIH)
%
t
c(CI)
120 < XCLKIN
≤
150 MHz
45
55
(1)
Not production tested.
Table 6-7. Possible PLL Configuration Modes
(1)
PLL MODE
REMARKS
SYSCLKOUT
Invoked by tying XPLLDIS pin low upon reset. PLL block is completely disabled. Clock input to the
PLL Disabled
XCLKIN
CPU (CLKIN) is directly derived from the clock signal present at the X1/XCLKIN pin.
Default PLL configuration upon power-up, if PLL is not disabled. The PLL itself is bypassed.
PLL Bypassed However, the /2 module in the PLL block divides the clock input at the X1/XCLKIN pin by two before
XCLKIN/2
feeding it to the CPU.
Achieved by writing a non-zero value n into PLLCR register. The /2 module in the PLL block now
PLL Enabled
(XCLKIN × n)/2
divides the output of the PLL by two before feeding it to the CPU.
(1)
Not production tested.
6.13.2 Output Clock Characteristics
Table 6-8. XCLKOUT Switching Characteristics (PLL Bypassed or Enabled)
(1) (2)
NO.
PARAMETER
MIN
TYP
MAX
UNIT
C1
t
c(XCO)
Cycle time, XCLKOUT
6.67
(3)
ns
C3
(4)
t
f(XCO)
Fall time, XCLKOUT
2
ns
C4
(4)
t
r(XCO)
Rise time, XCLKOUT
2
ns
C5
(4)
t
w(XCOL)
Pulse duration, XCLKOUT low
H–2
H+2
ns
C6
(4)
t
w(XCOH)
Pulse duration, XCLKOUT high
H–2
H+2
ns
C7
(4)
t
p
PLL lock time
(5)
131 072t
c(CI)
ns
(1)
A load of 40 pF is assumed for these parameters.
(2)
H = 0.5t
c(XCO)
(3)
The PLL must be used for maximum frequency operation.
(4)
Not production tested..
(5)
This parameter has changed from 4096 XCLKIN cycles in the earlier revisions of the silicon.
Copyright © 2009–2010, Texas Instruments Incorporated
Electrical Specifications
95
Product Folder Link(s):