Empire Comfort Systems DV-25-2SG 사용자 설명서

12434-8-0806

Page 11

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING:  If you do not follow these instructions exactly, a fire or explosion may result caus-

ing property damage, personal injury or loss of life.

A.   This appliance has a pilot which must be lighted by hand.  

When lighting the pilot, follow these instructions exactly.

B.   BEFORE LIGHTING  smell all around the appliance area 

for gas.  Be sure to smell next to the floor because some 

gas is heavier than air and will settle on the floor.

 

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; 

  do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's 

phone.  Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the fire 

department.

C.   Use only your hand to push in or turn the gas control 

knob.  Never use tools.  If the knob will not push in 

or turn by hand, don't try to repair it; call  a  qualified 

service technician.  Force or attempted repair may result 

in a fire or explosion.

D.   Do not use this appliance if any part has been under 

water.  Immediately call a qualified service technician 

to inspect the appliance and to replace any part of the 

control system and any gas control which has been under 

water.

TO TURN OFF GAS TO APPLIANCE

1.   Set the thermostat to lowest setting.

2.   Turn off all electric power to appliance if service is to be 

performed (if applicable).

3.   Remove casing front assembly.

4.   Push in gas control knob slightly and turn clockwise  

 to "OFF." Do not force.

5.   Replace casing front assembly.

1.   STOP!   Read the safety information above.
2.  Set the thermostat to lowest setting.
3.  Turn  off  all  electric  power  to  the  appliance    (if  appli-

cable).

4.   Remove casing front assembly.
5.   Push in gas control knob slightly and turn clockwise    

 to "OFF".

 

 

NOTE:  Knob cannot be turned from "PILOT" to "OFF" 

unless knob is pushed in slightly.  Do not force.

6.   Wait ten (10) minutes to clear out any gas.  Then smell 

for gas, including near the floor.  If you smell gas, STOP! 

Follow "B" in the safety information above.  If you don't 

smell gas, go to the next step.

7.   Remove the pilot access cover located on the combustion 

chamber.  

8.   Find pilot - follow metal tube 

 

from gas control.  The pilot is 

 

behind the pilot access cover.

9.   Turn knob on gas control counterclockwise  
 

to "PILOT."

10.  Push in control knob all the way and hold in.  Imme-

diately light the pilot with the Piezo Pilot Ignitor or a 

match.  Continue to hold the control knob in for about 

one (1) minute after the pilot is lit.  Release knob,  and 

it will pop back up.  Pilot should remain lit.  If it goes 

out, repeat steps 5 through 10.

  • If knob does not pop up when released, stop 

and immediately call your service technician 

or gas supplier.  

  • If the pilot will not stay lit after several tries, 

turn the gas control knob to "OFF" and call 

your service technician or gas supplier.  

11.  Replace pilot access cover.
12.  Turn  gas  control  knob  counterclockwise 

  to 

"ON."

13. Replace casing front assembly.
14.  Turn  on  all  electric  power  to  the  appliance  (if  appli-

cable).

15.  Set thermostat to desired setting.
16.  CAUTION:  Pilot access cover must be kept tightly closed 

during operation.

LIGHTING INSTRUCTIONS