JVC LPT1029-001A 사용자 설명서

Masterpage:Right+

Filename [MH50SEK_09Timer Recording.fm]

Page 49Friday, 14 January 2005  16:44

You can programme this unit to timer record as many as 
16 programmes.
If you do not know the PlusCode number for the programme you 
wish to record, use the following procedure to set your unit to timer 
record the programme.

Load a recordable disc if recording to DVD. 

Press PROGRAMME to access the programme top screen.

Press selection keys to select 

ENTER.

●

When 

B appears on the TV screen, you need to 

cancel some of the reserved programmes. (A pg. 50)

Press selection keys to select the desired date, then press 
ENTER.

Press selection keys 
to select 

B, then press 

ENTER. Press 
selection keys to 
select the desired 
recording deck, then 
press ENTER.

Press selection keys 
to select 

then press ENTER. 
Press selection keys to set the desired start time, then press 
ENTER.

●

Each press of 

F G increases/decreases the start time in 

1 minute interval.

●

To increase/decrease the start time in 30 minutes interval, 
press and hold 

Press selection keys to select 

ASTOPB, then press ENTER. 

Press selection keys to set the desired stop time, then press 
ENTER.

●

Each press of 

F G increases/decreases the stop time in 

1 minute interval.

●

To increase/decrease the stop time in 30 minutes interval, 
press and hold 

Press selection keys to select 

ATV PROGB, then press 

ENTER. Press selection keys to select the desired channel.

Press selection keys to select 

ENTER.

Set the other recording options as required.

●

Refer to step 8 in 

Press selection keys 
to select 

AOKB, then 

press ENTER to 
access the 
Programme 
Confirmation screen.

Press selection keys 
to select 

AEXITB, then 

press ENTER to 
complete timer 
programming.

●

To programme another timer, press selection keys to select 
ACONTINUEB, then press ENTER.

●

APROGRAMME OVERLAPPEDB appears on the TV screen, 

delete or modify the programmes.

●

When two successive programmes are recorded on a DVD-RW 
disc with Manual Timer Programming function, the beginning of 
the second one may be left off the recording.

●

If the copy limited programme is received during timer recording, 
the unit enters Record Pause mode. Recording starts again if it is 
switched to a recordable broadcast during the time you 
programmed.

●

Make sure that the unit’s built-in clock is set properly.

●

Turn on the unit.

●

Turn on the TV and select the AV mode.

●

Slide the TV/CABLE/SAT/DVD switch to DVD.

FGDE

CABLE/SAT

DVD

TV

BBC1

[MISC. ] XP

BBC1

23:00

22:30

HDD

[0]: SAT

PROGRAMME > CALENDAR PR. (2/3)

CONFIRM

14/01/04 WED 22:30 - 23:00

RECORD TO

STOP

START

TV PROG

ENTER

SELECT

PROGRAMME

EXIT

PRESS [PROGRAMME] 

TO EXIT

SELECT WITH @ 

THEN PRESS [ENTER]

Satellite Receiver Users
To timer record a satellite broadcast using Manual Timer 
Programming:
A Perform ASatellite Receiver Control SettingB (A pg. 24).

B Perform AManual Timer ProgrammingB (A pg. 49).

In step 8, press AUX to change 

ATV PROGB to ASATB. Then 

press selection keys to enter the channel position for the 
satellite broadcast.

C Leave the satellite receiver’s power on.

Relief Recording
When a programme that is set for the DVD deck cannot be 
recorded properly, the programme is recorded to the HDD deck 
instead in XP mode.

●

If the remaining capacity of the hard disc is not sufficient, the 
programme is recorded to the DVD deck until the remaining 
capacity of the DVD disc lasts.

●

AJUSTB is selected for the recording mode, the current 

recording mode for the DVD deck is applied.

BBC1

1:00

28:00

PROGRAMME > CALENDAR PR. (3/3)

OK

INPUT TITLE

CATEGORY

VPS/PDC

WEEKLY/DAILY

REC MODE

GARDENING

EDUCATION

OFF

MON-FRI (FOR A WEEK)

FR360

14/01/04 WED 22:30 - 23:00
GARDENING

[EDUCATION] FR360

ENTER

SELECT

PROGRAMME

EXIT

PRESS [PROGRAMME] 

TO EXIT

SELECT WITH @ 

THEN PRESS [ENTER]

MH50SEK_00.book  Page 49  Friday, January 14, 2005  4:44 PM