JVC LPT1081-001A 사용자 설명서
17
G
ett
ing
S
S
tarted
EN
Channel setting
Tuning of this unit to broadcast channels can be
performed in two ways.
performed in two ways.
Auto tuning
Programme the tuner to scan only the channels you
can receive in your area.
can receive in your area.
1
Press [STANDBY/ON y/I] to turn on
the unit.
the unit.
2
Turn the TV on and select the input
to which the unit is connected.
to which the unit is connected.
3
In stop mode, press [SET UP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
will appear.
4
Select “Channel” using
[Cursor
[Cursor
U / D], then press [ENTER].
5
Select “Auto Tuning” using
[Cursor
[Cursor
U / D], then press [ENTER].
The unit will start storing channels available in
your area.
your area.
Wait for several minutes to finish channel storing.
6
Press [SET UP] to exit.
You can select only the channels memorized in
this unit by using [PR
this unit by using [PR
+/-
].
To select a channel
You can select a channel using [PR
You can select a channel using [PR
+/-
], or directly
enter the channel using [the Number buttons] on the
remote control.
remote control.
To cancel auto tuning
Press [RETURN] or [SET UP] during scanning.
Press [RETURN] or [SET UP] during scanning.
Note
• The selection will be affected by how you receive TV
channels in your local area.
• If the auto tuning is cancelled during scanning,
some channels not yet tuned may not be received.
• Sorting of TV channels from P01 to P06 will be
performed automatically as follows.
P01: BBC1
P01: BBC1
P02: BBC2
P03: ITV
P04: CH4
P05: CH5
P06: SKY NEWS
* If you are using a satellite receiver, turn it on and
select SKY NEWS before commencing tuning.
Manual tuning
Manually tune each channel.
1
In stop mode, press [SET UP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
will appear.
2
Select “Channel” using
[Cursor
[Cursor
U / D], then press [ENTER].
3
Select “Manual Tuning” using
[Cursor
[Cursor
U / D], then press [ENTER].
4
Select “Position” using
[Cursor
[Cursor
U / D], then press [ENTER].
5
Select the position number you wish
to use using [the Number buttons] or
[Cursor
to use using [the Number buttons] or
[Cursor
U / D], then press
[RETURN].
You can select position numbers 01 to 99.
6
Select “Channel” using
[Cursor
[Cursor
U / D], then press [ENTER].
7
Press [Cursor
U / D] to start
scanning.
• The tuner will begin to search up or down
automatically. When a channel is found, the unit
will stop searching and the picture will appear
on the TV screen.
will stop searching and the picture will appear
on the TV screen.
• You can select a desired channel number using
[the Number buttons]. Refer to the following
Channel Plan table and press the three digits to
select the channel number.
(To select channel 4, press [0] first and then
press [0] and [4]. Or press [4] and then “– – 4”
appears and wait for 2 seconds.)
Channel Plan table and press the three digits to
select the channel number.
(To select channel 4, press [0] first and then
press [0] and [4]. Or press [4] and then “– – 4”
appears and wait for 2 seconds.)
• If this is the channel you want, press
[RETURN].
This unit can receive the Hyper and Oscar
frequency bands.
frequency bands.
Auto Tuning Now
Channel Plan
Ch. Indication
TV Channel
01 - 10
IRA - IRJ, GAP
21 - 69
E21 - E69
74 - 78
X, Y, Z, Z+1, Z+2
80 - 99, 100
S1 - S20, GAP
121 - 141
S21 - S41
Channel
12
Decoder
OFF
Skip
ON
Position
P01
Manual Tuning
E6851BD_EN.book Page 17 Tuesday, August 2, 2005 5:57 PM