JVC LPT1081-001A 사용자 설명서
18
G
ett
ing
S
S
tarted
EN
• If “Skip” is set to “ON,” select “Skip” using
[Cursor
U / D], then press [ENTER]. Select
“OFF” using [Cursor
U / D], then press
[RETURN].
• If you want to decode scrambled signals, select
“Decoder” using [Cursor
U / D], then press
[ENTER]. Select “ON” using [Cursor
U / D],
then press [RETURN].
• To store another channel, repeat steps 4 to 7.
8
After completion, press [SET UP] to
exit.
exit.
To select a channel
Notes on using the Number buttons:
• Enter channel numbers as a two-digit number for
• Enter channel numbers as a two-digit number for
the quickest result. For example, to select channel
6, press [0] and [6]. If you only press [6], channel 6
will be selected after 2 seconds. You can only select
channels 1 to 99.
6, press [0] and [6]. If you only press [6], channel 6
will be selected after 2 seconds. You can only select
channels 1 to 99.
• You can select the external input mode “AV1”,
“AV2”, “AV3” or “AV4.”
• To select “AV1,” press [0], [0], [1].
• To select “AV2,” press [0], [0], [2].
• To select “AV3,” press [0], [0], [3].
• To select “AV4,” press [0], [0], [4].
• To select “AV2,” press [0], [0], [2].
• To select “AV3,” press [0], [0], [3].
• To select “AV4,” press [0], [0], [4].
To skip a Preset channel
You can set the unit to skip channels you can no
longer receive or seldom watch when you access
channels using [PR
longer receive or seldom watch when you access
channels using [PR
+/-
].
1
Follow steps 1 to 3 in “Manual
tuning.”
tuning.”
2
Select “Position” using
[Cursor
[Cursor
U / D], then press [ENTER].
3
Select the position number you wish
to skip using [the Number buttons]
or [Cursor
to skip using [the Number buttons]
or [Cursor
U / D], then press
[RETURN].
4
Select “Skip” using [Cursor
U / D],
then press [ENTER].
5
Select “ON” using [Cursor
U / D],
then press [RETURN].
• To skip another channel, repeat steps 2 to 5.
6
Press [SET UP] to exit.
Move
You can replace two channels.
1
In stop mode, press [SET UP].
2
Select “Advanced Setting Menu”
using [Cursor
using [Cursor
U / D], then press
[ENTER].
If it has already appeared, proceed to step 3.
3
Select “Channel” using
[Cursor
[Cursor
U / D], then press [ENTER].
4
Select “Move” using [Cursor
U / D],
then press [ENTER].
5
Select the position number of which
you want to change the channel
using [Cursor
you want to change the channel
using [Cursor
U / D], then press
[ENTER].
You cannot select a position number where
“– – –” appears next to the number, because
“Skip” is set to “ON” for that position number.
“– – –” appears next to the number, because
“Skip” is set to “ON” for that position number.
6
Move the channel to another
position number using
[Cursor
position number using
[Cursor
U / D], then press [ENTER].
• To move another channel, repeat steps 5 to 6.
7
Press [SET UP] to exit.
E6851BD_EN.book Page 18 Tuesday, August 2, 2005 5:57 PM