ONKYO HT-R340 Manual Do Utilizador
57
Advanced Setup
—Continued
The following table shows the display indicators for each
supported digital signal format.
supported digital signal format.
Normally, the AV receiver detects the signal format auto-
matically. However, if you experience either of the fol-
lowing issues when playing PCM or DTS material, you
can manually set the signal format to PCM or DTS:
• If the beginnings of tracks from a PCM source are cut
matically. However, if you experience either of the fol-
lowing issues when playing PCM or DTS material, you
can manually set the signal format to PCM or DTS:
• If the beginnings of tracks from a PCM source are cut
off, try setting the format to PCM.
• If noise is produced when fast forwarding or reversing
a DTS CD, try setting the format to DTS.
When using progressive scanning on your DVD player,
you may find that the picture and sound are out of sync.
With this setting, you can correct this by delaying the
audio signals. You can set it to 0, 20, or 40 milliseconds.
you may find that the picture and sound are out of sync.
With this setting, you can correct this by delaying the
audio signals. You can set it to 0, 20, or 40 milliseconds.
Note:
• This setting is not available when the Direct listening
mode is used with an analog input signal.
Digital Input Signal Formats
Format
Display
Dolby Digital
DTS
PCM
1
Press and hold the AV receiver’s [DIGITAL
INPUT] button for about 3 seconds.
INPUT] button for about 3 seconds.
2
While “Auto” is displayed (about 3 sec-
onds), press the [DIGITAL INPUT] button
again to select: PCM, DTS, or Auto.
onds), press the [DIGITAL INPUT] button
again to select: PCM, DTS, or Auto.
DTS or PCM:
The DTS or PCM indicator,
depending on which format you have set, flashes,
and only signals in that format are output. Digital
signals in other formats are ignored.
and only signals in that format are output. Digital
signals in other formats are ignored.
Auto (default):
The format is detected automati-
cally. If no digital input signal is present, the cor-
responding analog input is used instead.
responding analog input is used instead.
PCM
TONE
+
STEREO
LISTENING MODE
DISPLAY DIGITAL INPUT
RT/PTY/TP MEMORY TUNING MODE
RETURN
TUNING / PRESET
ENTER
SETUP
STANDBY
STANDBY/ON
CLEAR
PHONES
MULTl CH
DVD
VIDEO 1/VCR
VIDEO 2
VIDEO 3
TAPE
TUNER
CD
MASTER VOLUME
A SPEAKERS B
DIGITAL INPUT
Correcting Sound and Picture Sync
1
Press the [RECEIVER] REMOTE
MODE button.
MODE button.
2
Press and hold, for more than 4
seconds, the input selector but-
ton for the input source that you
want to correct.
seconds, the input selector but-
ton for the input source that you
want to correct.
This can be the [DVD], [VIDEO 1],
[VIDEO 2], or [VIDEO 3] input
source.
[VIDEO 2], or [VIDEO 3] input
source.
3
Use the Left and Right [
]/[
]
buttons to set the delay to 0, 20,
or 40 milliseconds.
or 40 milliseconds.
The previous display reappears if you
don’t do anything for 5 minutes.
don’t do anything for 5 minutes.
MUTING
MENU
TOP MENU
SP A / B
SETUP
RETURN
PLAYLIST
PLAYLIST
--/---
TAPE
ON/STANDBY
DIMMER
SLEEP
INPUT SELECTOR
REMOTE MODE
V
1
V
2
V
3
C D
TAPE
TUNER
DVD
MULTI CH
VOL
HDD
CDR
MD
DVD
RECEIVER
C D
+10
0
CLR
1
2
3
4
5
6
7
8
9
ENTER
CH
DISC
ALBUM
RECEIVER
INPUT
SELECTOR
RECEIVER
V
1
V
2
V
3
DVD
HT-S3100_3105_En.book Page 57 Friday, February 1, 2008 9:14 AM