ONKYO HT-S5300 Manual Do Utilizador

En

With the supplied UP-A1 Dock, you can easily play the 
music, photo, or movie stored on your Apple iPod through 
the AV receiver and enjoy great sound.
You can use the AV receiver’s remote controller to operate 
your iPod.

■

■

1. Turn on the AV receiver, and select 

the PORT selector.

2. Align your iPod with the Dock 

connector, and carefully place your 
iPod in the slot, as shown.

■

The adapter needs to be adjusted to 
match your particular iPod. If there’s a 
gap between the back of your iPod and 
the adapter, turn the adapter counterclockwise to close the 
gap. Turning the adapter counterclockwise moves it for-
ward. Turning it clockwise moves it backward.

• Make sure that the output level of the AV receiver is set to mini-

mum.

• To prevent damage to the dock connector, don’t twist your iPod 

when inserting or removing it, and be careful not to knock over 
the dock while your iPod is inserted.

• Do not take off your iPod from the Dock when you play back the 

music, photo, or movie stored on your iPod.

• Don’t use the UP-A1 with any other iPod accessories, such as 

FM transmitters and microphones, because they may cause a 
malfunction.

• It is recommended that you update your iPod software before 

using it with this unit. The updater for the iPod software is avail-
able at the Apple website.

■

Auto Power On
If you start iPod playback while the AV receiver is on 
Standby, the AV receiver will automatically turn on and 
select your iPod as the input source.
Direct Change
If you start iPod playback while listening to another input 
source, the AV receiver will automatically select your iPod 
as the input source.
Using the AV receiver’s Remote Controller
You can use the AV receiver’s remote controller to control 
basic iPod functions (

49).

■

You can use your iPod models Alarm Clock function to 
automatically turn on your iPod and the AV receiver at a 
specified time. The AV receiver’s input source will auto-
matically be set to the PORT selector.

• To use this function, your iPod must be in the UP-A1 Dock, and 

the UP-A1 Dock must be connected to the AV receiver.

• This function only works when the Standard mode is set to On.
• When you use this function, be sure to set the AV receiver’s vol-

ume control to a suitable level.

• When Zone 2 is turned on, you can’t use this function.
• You cannot use this function for sound effects on your iPod.

For the latest information on the Onkyo Dock compo-
nents, see the Onkyo web site at: 
http://www.onkyo.com
Before using the Onkyo Dock components, update 
your iPod with the latest software, available from the 
Apple web site.

Remove case 
before inserting

Backward

Forward

The AV receiver may take several seconds to startup, so 
you might not hear the first few seconds of the first 
song.

■

• Functionality depends on your iPod model and generation.
• Before selecting a different input source, stop iPod playback 

to prevent the AV receiver from selecting the iPod input 
source by mistake.

• If any accessories are connected to your iPod, the AV receiver 

may not be able to select the input source properly.

• When connecting UP-A1 Dock to the radio tuner UP-HT1 

(North American models)/UP-DT1 (Asian models) with 
AUTO selected by the tuner’s Mode Selector switch, you can 
switch the input source between UP-A1 Dock and the tuner, 
by pressing PORT repeatedly on the front panel.

• While your iPod is in the UP-A1 Dock, its volume control has 

no effect. If you adjust your iPod models volume control while 
it’s in the UP-A1 Dock, make sure it’s not set too high before 
you reconnect your headphones.

• The Auto Power On function will not work if you set your 

iPod in the UP-A1 Dock while it is playing.

• When Zone 2 is turned on, you can’t use Auto Power On and 

Direct Change functions.