Denon AVR-2310CI Manual Do Utilizador

0

Set  whether  or  not  to  use 
the front height channel.

ON : Use the front height channel.
OFF : Do not use the front height channel.
This can also be set by pressing

.

Attenuate  subwoofer  level 
when using EXT. IN mode.

ON : The input from the subwoofer channel is attenuated.
OFF : The input from the subwoofer channel is not attenuated. Usually use 
in this mode.

  Set this to “ON” if the subwoofer channel level seems too high when 

playing audio signal.

Turn  subwoofer  output  on 
and off.

ON : The subwoofer is used.
OFF : The subwoofer is not used.

Restores  all  the  surround 
parameter  settings  to  their 
defaults.

Yes : Reset to the defaults.
No : Do not reset to the defaults.

Sets the tone control function 
ON and OFF.

This  can  be  set  when 
“Dynamic EQ” (vpage 
51) is set to “OFF”.

ON : Allow tone adjustment (treble, bass).
OFF : Playback without tone adjustment.

  The tone cannot be adjusted when in the DIRECT mode.

Adjusts the low frequencies.

This  can  be  set  when 
“Tone  Control”  is  set  to 
“ON”.

Adjusts 

the 

high 

frequencies.

This  can  be  set  when 
“Tone  Control”  is  set  to 
“ON”.

Corrects 

the 

frequency 

response  of  the  different 
speakers.

• 

“MultEQ”  and  “Manual 
EQ”  settings  for  which 
“Not Used” has been set at 
“EQ Customize” (vpage 
32) cannot be selected.

•   When  using  headphones, 

“MultEQ” is set to “OFF”.

Audyssey : Optimize frequency response of all speakers.
Audyssey  Byp.L/R  :  Optimize  frequency  response  of  speakers  except 
front L and R speakers.
Audyssey  Flat  :  Optimize  frequency  response  of  all  speakers  to  flat 
response.
Manual : Apply frequency response set with “Manual EQ” (vpage 51).
OFF : The “MultEQ” equalizer cannot be used.

 • 

When  “Audyssey”,  “Audyssey  Byp.  L/R”  or  “Audyssey  Flat”  is 
selected, “

” lights.

• 

After  running Audyssey Auto  Setup,  if  the  Speaker  Configuration, 
Distance,  Channel  Level,  and  Crossover  Frequency  have  changed 
without increasing the number of speakers measured, only “

” 

lights.

• This can also be set by pressing 

.

• When the “Audyssey Auto Setup” (vpage 23) procedure is performed, the “MultEQ”, “Dynamic 

• Operating conditions for each function
  •   Dynamic EQ : 
 

When “MultEQ” is set to “ON”

  •   Dynamic Volume : 
 

When “Dynamic EQ” is set to “ON”

  •   Setting : 
 

When “Dynamic Volume” is set to “ON”

If  the  speaker  settings  are  changed  after  the  “Audyssey  Auto  Setup”  procedure  is  performed, 
“MultEQ”, “Dynamic EQ” and “Dynamic Volume” functions cannot be selected and “Run Audyssey” 
is displayed.
If this happens, either perform the “Audyssey Auto Setup” procedure again, or perform the “Restore” 
operation  (vpage  27)  to  restore  the  settings  to  as  they  were  after  the “Audyssey Auto  Setup” 
procedure was performed.

 

 

 : Moves the cursor (Up/Down/Left/Right) 

 : Decision the setting

 : Return to previous menu

:

  Displaying the menu

  Cancel the menu