Roland Fantom-X8 Manual Do Utilizador
189
Editing Songs
Extract Mode
Specifies whether you want to keep the sequencer data at the
destination.
destination.
Value
MIX:
The data at the destination will combine with the
extracted data.
extracted data.
REPLACE:
The data at the destination will be erased and
replaced by the extracted data.
replaced by the extracted data.
If you select “REPLACE,” only the sequencer data on the MIDI
channel specified by the Channel parameter will be the object of
the operation. Sequencer data of all other MIDI channels will be
unaffected.
channel specified by the Channel parameter will be the object of
the operation. Sequencer data of all other MIDI channels will be
unaffected.
Status
Selects the type of data to be extracted.
Value
ALL
NOTE
Poly Aftertouch
Control Change
Program Change
Channel Aftertouch
Pitch Bend
System Exclusive
Tune Request
Pattern Call
Range Min, Range Max
If you set the Status parameter to “NOTE,” “P.AFT,” “C.C,” or
“PROG,” specify the range of data. Set “Range Min” to the lowest
value of the range, and “Range Max” to the highest value of the
range.
“PROG,” specify the range of data. Set “Range Min” to the lowest
value of the range, and “Range Max” to the highest value of the
range.
To extract all notes or polyphonic aftertouch data, set “Range
Min” to “C -1,” and “Range Max” to “G9.” To extract C4, set
“Range Min” and “Range Max” to “C4.” To extract C3 through
C4, set “Range Min” to “C3” and “Range Max” to “C4.”
Min” to “C -1,” and “Range Max” to “G9.” To extract C4, set
“Range Min” and “Range Max” to “C4.” To extract C3 through
C4, set “Range Min” to “C3” and “Range Max” to “C4.”
• To extract all controller numbers, set “Range Min” to “0” and
“Range Max” to “127.” To extract all program numbers, set
“Range Min” to “1” and “Range Max” to “128.” To extract
number 4, set “Range Min” and “Range Max” to “4.” To extract
numbers 3 through 14, set “Range Min” to “3” and “Range
Max” to “14.”
“Range Min” to “1” and “Range Max” to “128.” To extract
number 4, set “Range Min” and “Range Max” to “4.” To extract
numbers 3 through 14, set “Range Min” to “3” and “Range
Max” to “14.”
This function shifts the timing of sequencer data backward or
forward in time within a specified area in steps of 1 tick. Slight shifts
of timing can speed up or drag performance.
forward in time within a specified area in steps of 1 tick. Slight shifts
of timing can speed up or drag performance.
When this function is executed, data that would be moved to a
point before the beginning of the song will automatically shift
to the beginning of the song. If data would be moved to a point
past the end of the song, additional new measures will be
created automatically as needed. The time signature of the
newly created measures will be the same as that of the measure
immediately preceding.
point before the beginning of the song will automatically shift
to the beginning of the song. If data would be moved to a point
past the end of the song, additional new measures will be
created automatically as needed. The time signature of the
newly created measures will be the same as that of the measure
immediately preceding.
fig.19-021_50
Track / Pattern (Source Track)
Specifies the track(s) or pattern whose sequencer data will be moved
in units of one tick.
in units of one tick.
Value
ALL:
Phrase tracks 1–16, the beat track, and the tempo
track
track
TRK 1–TRK 16:
The specified phrase track
TEMPO:
Tempo track
PTN001–PTN100:
The specified pattern
Ch / Part
Selects the MIDI channel of the data to be shifted in time.
To shift ticks of all sequencer data, set this parameter to ALL. To
shift the sequencer data tick of just one specific MIDI channel, select
that MIDI channel.
shift the sequencer data tick of just one specific MIDI channel, select
that MIDI channel.
Value:
ALL, Ch1–Ch16
If you set the Track parameter to “TEMPO,” or if the Status
parameter is set to “System Exclusive,” “Tune Request” or
“Pattern Call,” the Channel parameter will not be available.
parameter is set to “System Exclusive,” “Tune Request” or
“Pattern Call,” the Channel parameter will not be available.
Measure, For (Edit Range)
Specifies the range of measures in which the sequencer data will be
moved in units of one tick. If you set “For” to “ALL,” all measures
will be specified.
moved in units of one tick. If you set “For” to “ALL,” all measures
will be specified.
Shifting Performance Data
Forward and Back (Shift Clock)
Fantom-X678_r_e.book 189 ページ ２００５年５月１２日 木曜日 午後４時４０分