Roland Fantom-X8 Manual Do Utilizador

 

Effects not applied.

Check the following points.

• The “MFX,” “CHO,” “REV” or “MASTER” effect switches 

located in the upper part of the PLAY screen may have been 
turned off.

Press [EFFECTS]/[F8 (Effect Sw)] to turn them on.

• Are the various effect settings correct? (p. 206)

• If the send level of each effect is set to 0, the effect will not be 

applied. Check the settings.

• Even with send levels to each effect set at 0, effects are not 

applied if the Multi-effects Output Level, the Chorus Level, or 
the Reverb Level is set to 0. Check each setting.

• If Output Assign is set to other than “MFX,” the Multi-effects 

sound will not be output.

• If Output Assign is set to “PATCH” for each Part of the 

Performance, the sound will be output according to the Output 
Assign settings of the Patch (for each Tone) which is assigned to 
those Parts. This means that if Output Assign for the Patch 
(each Tone) is set to other than “MFX,” the Multi-effects sound 
will not be output.

The Modulation or other controller is always on.

The Fantom-X allows you to use the Matrix Control to control 
Patches in real time. The Matrix Control functions as the control 
source for the Control Change and other MIDI messages 
received by the Fantom-X, and makes changes to the various 
Patch parameters based on these messages.

Depending on these settings, the Fantom-X may be responding 
to MIDI messages sent from external MIDI devices, and may 
result the Patches sounding different than intended.

Raising the chorus or reverb send level for each part of a 
performance still does not cause the effect to be applied 
sufficiently.

Although you can make Send level settings to the Chorus and 

Reverb for each individual Part in a Performance, these values 
only set the upper limit of the Chorus and Reverb Send levels 
for the Patch used. Accordingly, even when the value is set to 
the maximum of 127, if the Send level is lowered in the Patch 
being used, there will be no effect. In addition, different Patch 
Chorus and Reverb Send level settings can be used according to 
whether or not the multi-effects are used.

Using the Matrix Control or other such means to control the 
LFO results in noise when the Pan is changed suddenly.

Lower the change in speed (LFO Rate).

Due to the specialized processing used for the Pan, which alters 
the volume level in each of the left and right sides, sudden Pan 
movements causing rapid changes in these levels creates large 
changes in volume, and noise from this may be audible as a 
result.

Multi-effect 43: TAP DELAY or other delay time value is set to 
the note, and then the tempo is slowed down, does the delay 
time not change beyond a fixed length?

Such Delay time settings have an upper limit, so if the upper 
limit of a value set to the note is exceeded when the tempo is 
retarded, that upper value cannot rise any further. The upper 
time limit for each is the maximum value that can be set other 
than the numerical value for the beat.

The Performance sounds different than when it was written.

Check the following points.

• If you have modified the settings of a patch used by a 

performance, or if the temporary patch of the performance has 
been modified by an external MIDI device, these patches must 
also be saved. 

If patches used by a performance have been edited when you 
write that performance, the Fantom-X will display a message 
asking whether you want to discard these patches. In such 
cases, first save the patch (p. 59) or rhythm set (p. 86), and then 
save the performance (p. 120) again.

• The Mastering Effect settings may have changed. (These 

settings are not stored as part of a performance.)

Patches sound different than when written.

Check the following points.

• The write operation cannot be used to save Patches as changed 

in Patch mode using Control Change messages from an external 
MIDI device.

 

 

Change messages that are received.

• The Mastering Effect settings may have changed. (These 

settings are not stored as part of a patch.)

The Arpeggio and D Beam controller settings in the 

Performance are different than those for the Patch.

Since the Fantom-X stores arpeggio and D Beam controller 

settings for each performance, it will operate according to the 
arpeggio and D Beam controller settings that were specified for 
each performance.

Fantom-X678_r_e.book 251 ページ ２００５年５月１２日　木曜日　午後４時４０分