Roland Fantom-X8 Manual Do Utilizador
74
Creating a Patch
Tone Out Level
Set the level of the signal that is sent to the output destination
specified by Tone Output Assign.
specified by Tone Output Assign.
Value:
0–127
Tone Chorus Send (Send Level (Output=MFX))
Specifies the level of the signal sent to the chorus for each tone if the
tone is sent through MFX.
tone is sent through MFX.
Value:
0–127
Tone Reverb Send (Send Level (Output=MFX))
Specifies the level of the signal sent to the reverb for each tone if the
tone is sent through MFX.
tone is sent through MFX.
Value:
0–127
Tone Chorus Send (Send Level (Output=non
MFX))
Sets the level of the signal sent to chorus for each tone if the tone is
not sent through MFX.
not sent through MFX.
Value:
0–127
Tone Reverb Send (Send Level (Output=non
MFX))
Sets the level of the signal sent to reverb for each tone if the tone is
not sent through MFX.
not sent through MFX.
Value:
0–127
fig.06-042_50
An LFO (Low Frequency Oscillator) causes change over a cycle
in a sound. Each tone has two LFOs (LFO1/LFO2), and these
can be used to cyclically change the pitch, cutoff frequency and
volume to create modulation-type effects such as vibrato, wah
and tremolo. Both LFOs have the same parameters so only one
explanation is needed.
in a sound. Each tone has two LFOs (LFO1/LFO2), and these
can be used to cyclically change the pitch, cutoff frequency and
volume to create modulation-type effects such as vibrato, wah
and tremolo. Both LFOs have the same parameters so only one
explanation is needed.
LFO 1/2
Waveform (LFO1/LFO2 Waveform)
Selects the waveform of the LFO.
Value
SIN:
Sine wave
TRI:
Triangle wave
SAW-U:
Sawtooth wave
SAW-D:
Sawtooth wave (negative polarity)
SQR:
Square wave
RND:
Random wave
BND-U:
Once the attack of the waveform output by the LFO
is allowed to develop in standard fashion, the
waveform then continues without further change.
is allowed to develop in standard fashion, the
waveform then continues without further change.
BND-D:
Once the decay of the waveform output by the LFO
is allowed to develop in standard fashion, the
waveform then continues without further change.
is allowed to develop in standard fashion, the
waveform then continues without further change.
TRP:
Trapezoidal wave
S&H:
Sample & Hold wave (one time per cycle, LFO value
is changed)
is changed)
CHAOS:
Chaos wave
VSIN:
Modified sine wave. The amplitude of a sine wave is
randomly varied once each cycle.
randomly varied once each cycle.
STEP:
A waveform generated by the data specified by LFO
Step 1–16. This produces stepped change with a
fixed pattern similar to a step modulator.
Step 1–16. This produces stepped change with a
fixed pattern similar to a step modulator.
If you set this to “BND-U” or “BND-D,” you must turn the Key
Trigger parameter to “ON.” If this is “OFF,” it will have no
effect.
Trigger parameter to “ON.” If this is “OFF,” it will have no
effect.
LFO Rate (LFO1/LFO2 Rate)
★
Adjusts the modulation rate, or speed, of the LFO.
Value:
0–127, Note
LFO Rate sets the beat length for the synchronized tempo is
synchronized with the tempo set in a sequencer.
synchronized with the tempo set in a sequencer.
(Example)
For a tempo of 120 (120 quarter notes occur in 1 minute (60 seconds))
This setting will be ignored if the Waveform parameter is set to
“CHAOS.”
“CHAOS.”
Modulating Sounds (LFO)
1
2
3
4
Setting
LFO Rate
(half note)
1 second (60 / 60 =1 (second))
(quarter note)
0.5 seconds (60 / 120= 0.5 (seconds))
(eighth note)
0.25 seconds (60 / 240= 0.25 (seconds))
1
Fantom-X678_r_e.book 74 ページ ２００５年５月１２日 木曜日 午後４時４０分