Aiwa CDC-X237 Manual Do Utilizador
3
ENGLISH
3
ENGLISH
Frequency
indication
indication
TUNER
indicator
indicator
Adjusting sound
You can select the following modes for adjusting sound
depending on the music you listen to: BASS (low
frequencies), TRE (high frequencies), BAL (left/right),
FAD (front/ rear) and H-BASS (high bass).
depending on the music you listen to: BASS (low
frequencies), TRE (high frequencies), BAL (left/right),
FAD (front/ rear) and H-BASS (high bass).
1
Press SEL repeatedly to select the mode to be
adjusted.
Pressing SEL cycles through the modes. The
selected mode’s indicator appears.
adjusted.
Pressing SEL cycles through the modes. The
selected mode’s indicator appears.
2
Turn Jog dial to increase/decrease the level or to
select on/off for the selected mode.
select on/off for the selected mode.
Note
Adjust the level or select on/off within 5 seconds, or the
selected mode will return to previous state.
selected mode will return to previous state.
Aligning the source levels
(Source Level Adjuster)
Volume may vary each time you change the source
mode. In this case, you can align each source mode’s
volume to almost the same level.
mode. In this case, you can align each source mode’s
volume to almost the same level.
1
Press Jog dial (PUSH-SOURCE) or TU (TUNER)
repeatedly to select the desired mode.
repeatedly to select the desired mode.
2
Press DSPL while pressing SEL.
“LA 0” appears on the display.
“LA 0” appears on the display.
3
Turn Jog dial to adjust the level.
Note
Adjust the level within 5 seconds, or the selected mode
will be canceled.
will be canceled.
Restoring the factory settings
1
Turn off the unit.
2
Press and hold DSPL until “LA --” appears on the
display.
display.
Note
You can restore the factory settings only for VOL, BASS,
TRE, BAL, FAD, and H-BASS, and aligned source
volume levels.
TRE, BAL, FAD, and H-BASS, and aligned source
volume levels.
Setting the beep tone
1
Turn off the unit.
2
Press and hold SEL until “bEEP” appears on the
display.
display.
3
Turn Jog dial to select on (level indicators appear)
or off (level indicators disappear).
or off (level indicators disappear).
4
Press SEL.
Setting the clock
1
Press and hold DSPL until the clock indicator
flashes on the display.
flashes on the display.
2
Press + (to set hour) or – (to set minute), and then
turn Jog dial.
turn Jog dial.
3
Press DSPL.
Displaying the clock
1
Press DSPL.
To return to the former display, press DSPL again.
RADIO OPERATION
Tuning in to a station
(Seek/Manual Tuning)
LO
TU (TUNER)
+/–
Local indicator
Stereo indicator
Band indicator
1
Press TU (TUNER) repeatedly to select the desired
band (FM1, FM2, FM3, AM1, or AM2).
band (FM1, FM2, FM3, AM1, or AM2).
2*
Press + (to move to higher frequencies) or – (to
move to lower frequencies) to tune in to a station.
“STEREO” appears on the display when an FM
station is broadcasting in stereo, and receiving
conditions are good.
move to lower frequencies) to tune in to a station.
“STEREO” appears on the display when an FM
station is broadcasting in stereo, and receiving
conditions are good.
*Seek Tuning and Manual Tuning
• Press and hold + or – until seek Tuning starts.
• Press and hold + or – until seek Tuning starts.
The unit locates a station automatically (Seek Tuning).
• Press + or – repeatedly to search for a desired station
while increasing or decreasing the frequency step by
step (Manual Tuning).
step (Manual Tuning).
To stop Seek Tuning, press + or – again.