ONKYO TX-SR8360 Manual Do Utilizador
66
Advanced Operations
—Continued
Adjusting Individual Speaker Levels
You can adjust the level of individual speakers while
using the DVD analog multichannel input.
using the DVD analog multichannel input.
Adjusting with onscreen setup menus:
Adjusting with the remote controller:
Notes:
• These speaker level settings are completely indepen-
dent of those explained on pages 50, 65.
• While the DVD analog multichannel input is selected,
you can only select the Direct, Pure Audio (not North
American TX-SR603), or Multich listening mode. If
you select the DVD analog multichannel input while
using another listening mode, that listening mode will
be cancelled.
American TX-SR603), or Multich listening mode. If
you select the DVD analog multichannel input while
using another listening mode, that listening mode will
be cancelled.
• While the DVD analog multichannel input is selected,
the Automatic Speaker Setup on page 39 and Speaker
Configuration settings on page 46 are ignored, and sig-
nals from the multichannel input are fed to the front left,
front right, center, surround left, and surround right
speakers, and subwoofer regardless of those settings.
Configuration settings on page 46 are ignored, and sig-
nals from the multichannel input are fed to the front left,
front right, center, surround left, and surround right
speakers, and subwoofer regardless of those settings.
This section explains how to record the current input
source, how to record one input source while enjoying
another, and how to dub audio onto your video record-
ings.
source, how to record one input source while enjoying
another, and how to dub audio onto your video record-
ings.
Unless you have the full consent of the copyright
holder, copyright laws prohibit using your recordings
for anything other than personal enjoyment!
holder, copyright laws prohibit using your recordings
for anything other than personal enjoyment!
Notes:
• The surround sound and DSP listening modes cannot
be recorded.
• Copy-protected DVDs cannot be recorded.
• You cannot record from the DVD analog multichannel
input.
• Various restrictions apply to digital recording. Refer
to the manuals supplied with your digital recording
equipment for more details.
equipment for more details.
• Digital input signals are output by only the digital out-
puts, and analog input signals are output by only the
analog outputs. There is no internal conversion from
digital to analog or vice versa.
analog outputs. There is no internal conversion from
digital to analog or vice versa.
• DTS signals will be recorded as noise, so don’t
attempt analog recording of DTS CDs or LDs.
• While the listening mode is set to Pure Audio, no
image is provided because the power is turned off for
the video circuit. If you want to make recordings,
select other listening mode.
the video circuit. If you want to make recordings,
select other listening mode.
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
lowed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [
]/[
]
buttons to select “3. Multich
Level Adjust,” and then press
[ENTER].
Level Adjust,” and then press
[ENTER].
The Multich Level Adjust menu
appears.
appears.
3
Use the Up and Down [
]/[
]
buttons to select each speaker,
and use the Left and Right [
and use the Left and Right [
]/
[
] buttons to set the volume.
The volume can be adjusted from –12
to +12 dB in 1 dB steps (–30 to +12 dB
for the subwoofer).
to +12 dB in 1 dB steps (–30 to +12 dB
for the subwoofer).
1
Use the remote controller’s [CH
SEL] button to select each
speaker, and then use the
[LEVEL–] and [LEVEL+] buttons
to adjust the volume.
SEL] button to select each
speaker, and then use the
[LEVEL–] and [LEVEL+] buttons
to adjust the volume.
The level can be adjusted from –12 to
+12 dB (–30 to +12 dB for the sub-
woofer).
+12 dB (–30 to +12 dB for the sub-
woofer).
RECEIVER
ENTER
ENTER
ENTER
CH SEL
LEVEL+
LEVEL-
Recording