ONKYO TX-SR8360 Manual Do Utilizador
70
Advanced Setup
—Continued
You can assign a default listening mode to each input
source that will be selected automatically when you
select each input source. For example, you can set the
default listening mode to be used with Dolby Digital
input signals. You can select other listening modes dur-
ing playback, but the mode specified here will be
resumed once the AV receiver has been set to Standby.
source that will be selected automatically when you
select each input source. For example, you can set the
default listening mode to be used with Dolby Digital
input signals. You can select other listening modes dur-
ing playback, but the mode specified here will be
resumed once the AV receiver has been set to Standby.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Assigning Listening Modes to Input
Sources
Sources
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
lowed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [
]/[
]
buttons to select “6. Input
Setup,” and then press [ENTER].
Setup,” and then press [ENTER].
The Input Setup menu appears.
3
Use the INPUT SELECTOR but-
tons on the remote controller to
select the input source that you
want to set.
tons on the remote controller to
select the input source that you
want to set.
For input selectors that have no digital
input jacks, only “b. Analog” will be
available.
input jacks, only “b. Analog” will be
available.
RECEIVER
ENTER
ENTER
4
Use the Up and Down [
]/[
]
buttons to select the signal for-
mat that you want to set, and
then use the Left and Right [
mat that you want to set, and
then use the Left and Right [
]/
[
] buttons to select a listening
mode.
Only listening modes that can be used
with each input signal format can be
selected.
For “Surround,” the listening mode
specified on page 69 will be used.
The Last Valid option means that the
listening mode selected last will be
used.
with each input signal format can be
selected.
For “Surround,” the listening mode
specified on page 69 will be used.
The Last Valid option means that the
listening mode selected last will be
used.
b. Ana/PCM:
With this setting, you
can specify the listening mode to be
used when an analog (CD, TV, LD,
VHS, MD, turntable, radio, cassette,
cable, satellite, etc.) or PCM digital
(CD, DVD, etc.) audio signal is played.
used when an analog (CD, TV, LD,
VHS, MD, turntable, radio, cassette,
cable, satellite, etc.) or PCM digital
(CD, DVD, etc.) audio signal is played.
c. Dolby D:
With this setting, you can
specify the listening mode to be used
when a Dolby Digital format digital
audio signal is played (DVD, etc.).
when a Dolby Digital format digital
audio signal is played (DVD, etc.).
d. DTS:
With this setting, you can
specify the listening mode to be used
when a DTS format digital audio signal
is played (DVD, LD, CD, etc.).
when a DTS format digital audio signal
is played (DVD, LD, CD, etc.).
e. D.F. 2ch:
With this setting, you can
specify the listening mode to be used
when a 2-channel (2/0) digital audio
signal (Dolby Digital, DTS) is played
(DVD, etc.).
when a 2-channel (2/0) digital audio
signal (Dolby Digital, DTS) is played
(DVD, etc.).
f. Mono:
With this setting, you can
specify the listening mode to be used
when a mono digital audio signal is
played (DVD, etc.).
when a mono digital audio signal is
played (DVD, etc.).
g. Multich:
This setting is available
only when DVD or MULTI CH is
selected with INPUT SELECTOR.
With this setting, you can specify the
listening mode to be used when the
DVD analog multichannel input is
used.
selected with INPUT SELECTOR.
With this setting, you can specify the
listening mode to be used when the
DVD analog multichannel input is
used.
5
When you’ve finished, press the
[SETUP] button.
[SETUP] button.
The setup menu closes.
ENTER