ONKYO TX-SR508 Manual Do Utilizador
41
En
Remote Control Settings
■
Remote ID
`
1, 2, or 3
When several Onkyo components are used in the same
room, their remote ID codes may overlap. To differenti-
ate the AV receiver from the other components, you can
change its remote ID from “1”, to “2” or “3”.
room, their remote ID codes may overlap. To differenti-
ate the AV receiver from the other components, you can
change its remote ID from “1”, to “2” or “3”.
Note
• If you do change the AV receiver’s remote ID, be sure to change
the remote controller to the same ID (see below), otherwise, you
won’t be able to control it with the remote controller.
won’t be able to control it with the remote controller.
Changing the Remote Controller’s ID
FM/AM Frequency Setup Settings
For FM/AM tuning to work properly, you must specify the
FM/AM frequency step used in your area. Note that when
this setting is changed, all radio presets will be deleted.
FM/AM frequency step used in your area. Note that when
this setting is changed, all radio presets will be deleted.
■
FM/AM Freq Step (North American models)
`
200k/10kHz:
Select if 200k/10kHz steps are used in your area.
`
50k/9kHz:
Select if 50k/9kHz steps are used in your area.
■
AM Freq Step (European and Asian models)
`
10kHz:
Select if 10kHz steps are used in your area.
`
9kHz:
Select if 9kHz steps are used in your area.
SIRIUS Settings (North American models)
See the separate Satellite Radio Guide for more informa-
tion.
tion.
■
SAT Radio
If you connect a SIRIUS Satellite Radio antenna to the
AV receiver (sold separately), set this setting to “SIR-
IUS”.
If you connect a SIRIUS Satellite Radio antenna to the
AV receiver (sold separately), set this setting to “SIR-
IUS”.
■
Antenna Aiming
■
Parental Lock
These items are for use with SIRIUS Satellite Radio.
It’s not available if “SAT Radio” is set to “None”.
These items are for use with SIRIUS Satellite Radio.
It’s not available if “SAT Radio” is set to “None”.
Menu
HDMI Setup
■
Audio TV OUT
`
Off:
HDMI audio is not output.
`
On:
HDMI audio is output.
This preference determines whether audio received at the
HDMI IN is output by the HDMI OUT. You may want to
turn this preference on if your TV is connected to the
HDMI OUT and you want to listen to the audio from a
component that’s connected to an HDMI IN, through your
TV’s speakers. Normally, this should be set to “Off”.
HDMI IN is output by the HDMI OUT. You may want to
turn this preference on if your TV is connected to the
HDMI OUT and you want to listen to the audio from a
component that’s connected to an HDMI IN, through your
TV’s speakers. Normally, this should be set to “Off”.
Note
• If
“
On
”
is selected and the signal can be output by the TV, the
AV receiver will output no sound through its speakers.
• If “On” is selected, “TV Sp On” appears on the display by
pressing DISPLAY.
• When
“
TV Control
”
is set to
“
On
”
, this setting is fixed to
“
Auto
”
.
• With some TVs and input signals, no sound may be output even
when this setting is set to
“
On
”
.
• When the “Audio TV OUT” setting is set to
“
On
”
, or
“
TV Con-
trol” is set to
“
On
”
and you’re listening through your TV’s
speakers (
15), if you turn up the AV receiver’s volume con-
trol, the sound will be output by the AV receiver’s front left and
right speakers. To stop the AV receiver’s speakers producing
sound, change the settings, change your TV’s settings, or turn
down the AV receiver’s volume.
right speakers. To stop the AV receiver’s speakers producing
sound, change the settings, change your TV’s settings, or turn
down the AV receiver’s volume.
■
LipSync
`
Disable:
HDMI lip sync disabled.
`
Enable:
HDMI lip sync enabled.
The AV receiver can be set to automatically correct any
delay between the video and the audio, based on the data
from the connected monitor.
delay between the video and the audio, based on the data
from the connected monitor.
Note
• This function works only if your HDMI-compatible TV supports
HDMI Lip Sync.
• You can check the amount of delay being applied by the HDMI
Lip Sync function on the A/V Sync screen.
1
While holding down
RECEIVER, press and hold
down
SETUP until the remote indicator lights
(about 3 seconds) (
2
Use the number buttons to enter ID 1, 2, or 3.
The remote indicator flashes twice.
The remote indicator flashes twice.
HDMI Setup