ONKYO TX-SR604E Manual Do Utilizador
47
First Time Setup
—Continued
If you connect an
-capable Onkyo MiniDisc
recorder, CD recorder, or next generation HDD-compat-
ible component to the TAPE IN/OUT or VIDEO 3 IN
jacks, for
ible component to the TAPE IN/OUT or VIDEO 3 IN
jacks, for
to work properly, you must change this
setting.
This setting can only be changed on the AV receiver.
iPod photo: If you’re using an iPod photo with the
DS-A1 Remote Interactive Dock, connect the DS-A1 to
the VIDEO 3 IN jacks.
DS-A1 Remote Interactive Dock, connect the DS-A1 to
the VIDEO 3 IN jacks.
Note:
HDD can be selected for the TAPE input selector or
VIDEO 3 input selector, but not both at the same time.
HDD can be selected for the TAPE input selector or
VIDEO 3 input selector, but not both at the same time.
If the impedance of any speaker is 4 ohms or more but
less than 6, set the minimum speaker impedance to 4
ohms.
less than 6, set the minimum speaker impedance to 4
ohms.
Note:
Before you change this setting, turn down the volume.
Before you change this setting, turn down the volume.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Changing the Input Display
1
Press the [TAPE] or [VIDEO 3]
input selector button so that
“TAPE” or “VIDEO 3” appears on
the display.
input selector button so that
“TAPE” or “VIDEO 3” appears on
the display.
2
Press and hold down the [TAPE]
or [VIDEO 3] input selector but-
ton (about 3 seconds) to change
the setting.
or [VIDEO 3] input selector but-
ton (about 3 seconds) to change
the setting.
Repeat this step to select MD, CDR, or
HDD.
For the TAPE input selector, the setting
changes in this order:
HDD.
For the TAPE input selector, the setting
changes in this order:
TAPE
→
MD
→
CDR
→
HDD
For the VIDEO 3 input selector, the set-
ting changes in this order:
ting changes in this order:
VIDEO 3
↔
HDD
1, 2
1, 2
TAPE
VIDEO
3
TAPE
VIDEO
3
→
Minimum Speaker Impedance (not
North American models)
North American models)
1
Press the [RECEIVER] button,
followed by the [SETUP] button.
followed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [
]/[
]
buttons to select “8. Hardware
Setup,” and then press [ENTER].
Setup,” and then press [ENTER].
The Hardware Setup menu appears.
3
Use the Up and Down [
]/[
]
buttons to select “SP Imped-
ance,” and then use the Left and
Right [
ance,” and then use the Left and
Right [
]/[
] buttons to select:
4 ohms: Select if the impedance of any
speaker is 4 ohms or more but
less than 6.
less than 6.
6 ohms: Select if the impedances of all
speakers are between 6 and
16 ohms.
16 ohms.
4
Press the [SETUP] button.
Setup closes.
If you change this setting, you must run the automatic
speaker setup again (see page 38).
speaker setup again (see page 38).
RECEIVER
SETUP
8.Hardware Setup
------------------------
a.SP Impedance :6ohms
b.PoweredZone2:NotAct
c.TV Format :Auto
d.AM Freq. Step: 9kHz
e.Remote ID :1
f.HDMI Audio Out :Off
g.SW Input Sensitivity
: 0dB
------------------------
a.SP Impedance :6ohms
b.PoweredZone2:NotAct
c.TV Format :Auto
d.AM Freq. Step: 9kHz
e.Remote ID :1
f.HDMI Audio Out :Off
g.SW Input Sensitivity
: 0dB
SETUP