ONKYO TX-SR703E Manual Do Utilizador
46
First Time Setup
—Continued
If you connect an
-capable Onkyo MiniDisc
recorder, CD recorder, or next generation HDD-compat-
ible component to the TAPE IN/OUT or VIDEO 3 IN
jacks, for
ible component to the TAPE IN/OUT or VIDEO 3 IN
jacks, for
to work properly, you must change this
setting.
This setting can only be changed on the AV receiver.
iPod photo:
If you’re using an iPod photo with the
DS-A1 Remote Interactive Dock, connect the DS-A1 to
the VIDEO 3 IN jacks.
the VIDEO 3 IN jacks.
Note:
HDD can be selected for the TAPE input selector or
VIDEO 3 input selector, but not both at the same time.
VIDEO 3 input selector, but not both at the same time.
If the impedance of any speaker is 4 ohms or more but
less than 6, set the Minimum Speaker Impedance to 4
ohms.
less than 6, set the Minimum Speaker Impedance to 4
ohms.
Note:
Before you change this setting, turn down the volume.
Notes:
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
and [ENTER] button.
Changing the Input Display
1
Press the [TAPE] or [VIDEO 3]
input selector button so that
“TAPE” or “VIDEO3” appears on
the display.
input selector button so that
“TAPE” or “VIDEO3” appears on
the display.
2
Press and hold down the [TAPE]
or [VIDEO 3] input selector but-
ton (about 3 seconds) to change
the setting.
or [VIDEO 3] input selector but-
ton (about 3 seconds) to change
the setting.
Repeat this step to select MD, CDR, or
HDD.
For the TAPE input selector, the setting
changes in this order:
HDD.
For the TAPE input selector, the setting
changes in this order:
TAPE
→
MD
→
CDR
→
HDD
→
For the VIDEO 3 input selector, the set-
ting changes in this order:
ting changes in this order:
VIDEO 3
→
HDD
→
VIDEO 3
→
PUSH TO OPEN
STANDBY/ON
STANDBY
MASTER VOLUME
PHONO
ZONE 2
DISPLAY
PURE AUDIO
TUNER
TAPE
VIDEO 4
VIDEO 3
VIDEO 2
VIDEO 1
DVD
MULTI CH
CD
OFF
ON
POWER
1, 2
1, 2
VIDEO 3
or
TAPE
or
TAPE
VIDEO 3
Minimum Speaker Impedance
1
Press the [RECEIVER] button,
followed by the [SETUP] button.
followed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [
]/[
]
buttons to select “3. Speaker
Setup,” and then press [ENTER].
Setup,” and then press [ENTER].
The Speaker Setup menu appears.
3
Use the Up and Down [
]/[
]
buttons to select “Speaker
Impedance,” and then press
[ENTER].
Impedance,” and then press
[ENTER].
4
Use the Left and Right [
]/[
]
buttons to select:
4 ohms:
Select if the impedance of any
speaker is 4 ohms or more but
less than 6.
speaker is 4 ohms or more but
less than 6.
6 ohms:
Select if the impedances of all
speakers are between 6 and
16 ohms.
speakers are between 6 and
16 ohms.
5
Press the [SETUP] button.
Setup closes.
If you change this setting, you must run the automatic
speaker setup again (see page 40).
speaker setup again (see page 40).
RECEIVER
ENTER
ENTER
3.Speaker Setup
------------------------
0.Speaker Impedance
2.Speaker Configuration
3.Speaker Distance
4.Level Calibration
5.THX Audio Setup
6.Equalizer Settings
------------------------
0.Speaker Impedance
2.Speaker Configuration
3.Speaker Distance
4.Level Calibration
5.THX Audio Setup
6.Equalizer Settings
1.Speaker Impedance
ENTER
TX-SR803_En.book Page 46 Friday, August 26, 2005 9:26 AM