ONKYO TX-SR703E Manual Do Utilizador
84
Zone 2
—Continued
Controlling Zone 2 with the Remote
Controller
Note:
• To control Zone 2, you must press the remote control-
ler’s [ZONE 2] REMOTE MODE button first.
Adjusting the Volume for Zone 2
To Mute Zone 2:
Press the remote controller’s [ZONE 2] button, followed
by the [MUTING] button. To unmute Zone 2, press the
remote controller’s [ZONE 2] button again, followed by
the [MUTING] button, or adjust the volume for Zone 2.
by the [MUTING] button. To unmute Zone 2, press the
remote controller’s [ZONE 2] button again, followed by
the [MUTING] button, or adjust the volume for Zone 2.
Notes:
• Only analog input sources are output by the ZONE 2
LINE OUT and ZONE 2 SPEAKERS terminals. Dig-
ital input sources are not output. If no sound is heard
when an input source is selected, check to see if it’s
connected to an analog input.
ital input sources are not output. If no sound is heard
when an input source is selected, check to see if it’s
connected to an analog input.
• When the ZONE 2 SPEAKERS terminals are used,
listening modes that require surround back speakers,
such as Dolby Digital EX, DTS-ES, and THX Select2
Cinema, are unavailable.
such as Dolby Digital EX, DTS-ES, and THX Select2
Cinema, are unavailable.
• While Zone 2 is on, the
functions do not work.
• You can’t select different radio stations for the main
room and Zone 2. The same radio station will be used
for both.
for both.
1
Press the [ZONE 2] REMOTE
MODE button, then point the
remote controller at the AV
receiver and press the [ON] but-
ton.
MODE button, then point the
remote controller at the AV
receiver and press the [ON] but-
ton.
Zone 2 turns on, and the ZONE 2 12V
TRIGGER OUT goes high (+12 V).
TRIGGER OUT goes high (+12 V).
2
To select an input source for
Zone 2, press the [ZONE 2]
REMOTE MODE button, followed
by an INPUT SELECTOR button.
Zone 2, press the [ZONE 2]
REMOTE MODE button, followed
by an INPUT SELECTOR button.
To select AM, FM, or XM, press the
[TUNER] INPUT SELECTOR button
repeatedly.
[TUNER] INPUT SELECTOR button
repeatedly.
3
To turn off Zone 2, press the
[ZONE 2] REMOTE MODE button,
followed by the [STANDBY] but-
ton.
[ZONE 2] REMOTE MODE button,
followed by the [STANDBY] but-
ton.
THX
10
- - / - - -
11
12
REMOTE MODE
HDD
RECEIVER
TAPE/AMP
DVD
CD
ZONE2
STEREO
SURR
DIRECT
SUBTITLE
AUDIO
ALLST
PLAY MODE
VIDEO OFF
REPEAT
OPEN/CLOSE
Re-EQ
+
-
T V CH
T V VOL
LISTENING MODE
INPUT SELECTOR
3
2
MACRO
1
+10
0
CLEAR
1
2
3
4
5
6
7
8
9
INPUT
I
ON
STANDBY
T V
CD
V1
V2
V3
MULTI CH
DVD
TUNER
PHONO
V4
TAPE
PURE A
TEST TONE
CH SEL
LEVEL
LEVEL
L NIGHT
RC-620M
ZONE2
ON
STANDBY
LEVEL–,
LEVEL+
LEVEL+
INPUT
SELECTOR
ZONE2
ON
ZONE2
1
2
3
4
6
7
8
9
CD
V1
V4
V2
V3
DVD
TAPE
TUNER
+10
PHONO
ZONE2
STANDBY
1
On the remote controller, press
the [ZONE 2] REMOTE MODE but-
ton, and then use the [LEVEL–]
and [LEVEL+] buttons.
the [ZONE 2] REMOTE MODE but-
ton, and then use the [LEVEL–]
and [LEVEL+] buttons.
On the AV receiver, use the ZONE
2 LEVEL [
2 LEVEL [
]/[
] buttons.
If your Zone 2 speakers are connected
to an amp in Zone 2, use its volume
control to adjust the volume.
to an amp in Zone 2, use its volume
control to adjust the volume.
OFF
TONE
ZONE 2
ZONE 2 LEVEL
PHONES
STEREO
DIMMER
MEMORY
LISTENING MODE
TUNING
MODE
SETUP
PRESET
PRESET
TUNING
RETURN
ENTER
SETUP MIC
VIDEO
S VIDEO
DIGITAL
VIDEO 4 INPUT
AUDIO
L
R
CLEAR
STANDBY/ON
STANDBY
MASTER VOLUME
PHONO
ZONE 2
DISPLAY
PURE AUDIO
TUNER
TAPE
VIDEO 4
VIDEO 3
VIDEO 2
VIDEO 1
DVD
MULTI CH
CD
OFF
ON
POWER
ZONE 2 LEVEL ,
ZONE2
LEVEL
LEVEL
ZONE 2 LEVEL
AV receiver
TX-SR803_En.book Page 84 Friday, August 26, 2005 9:26 AM