ONKYO TX-SR503E Manual Do Utilizador
53
Controlling Other Components—Continued
Onkyo components that are connected via
can be
controlled by pointing the remote controller at the AV
receiver. This means that you can control such compo-
nents even if they are out of sight, for example, installed
in a rack.
receiver. This means that you can control such compo-
nents even if they are out of sight, for example, installed
in a rack.
If you want to control an Onkyo component by pointing
the remote controller directly at it, or you want to control
an Onkyo component that’s not connected via
the remote controller directly at it, or you want to control
an Onkyo component that’s not connected via
, enter
the following remote control codes:
[DVD] REMOTE MODE button
[DVD] REMOTE MODE button
0627: DVD player without
(default)
[CD/MD/CDR] REMOTE MODE button
1817: CD player without
(default)
0868: MD recorder without
1323: CD recorder without
1323: CD recorder without
Note:
If you connect an
If you connect an
-compatible Onkyo MiniDisc or
CD recorder to the TAPE IN/OUT jacks, for remote
operation to work properly, you must set the display to
MD or CDR (see page 31).
operation to work properly, you must set the display to
MD or CDR (see page 31).
If you’ve previously entered a code for a REMOTE
MODE button but now want to reset it, perform the fol-
lowing procedure.
MODE button but now want to reset it, perform the fol-
lowing procedure.
You can reset the remote controller to its default settings.
Remote Control Codes for Onkyo
Components Connected via
Components Connected via
1
Make sure the Onkyo component is con-
nected with an
nected with an
cable and an analog
audio cable (RCA).
See page 29 for details.
See page 29 for details.
2
Enter the appropriate remote control code
for the [DVD] or [CD] REMOTE MODE but-
ton.
[DVD] REMOTE MODE button
for the [DVD] or [CD] REMOTE MODE but-
ton.
[DVD] REMOTE MODE button
1612: DVD player with
[CD] REMOTE MODE button
1327: CD player with
1808: MD recorder with
1322: CD recorder with
1808: MD recorder with
1322: CD recorder with
See the previous page for information on entering
remote control codes.
remote control codes.
3
Press the [DVD] or [CD] REMOTE MODE
button, point the remote controller at the
AV receiver, and operate the component.
button, point the remote controller at the
AV receiver, and operate the component.
Resetting the REMOTE MODE
Buttons
Buttons
1
While holding down the REMOTE
MODE button that you want to
reset, press the [L NIGHT] button
for 3 seconds.
The REMOTE MODE button lights up.
MODE button that you want to
reset, press the [L NIGHT] button
for 3 seconds.
The REMOTE MODE button lights up.
2
Press the REMOTE MODE button
again.
The REMOTE MODE button is reset
and flashes twice.
again.
The REMOTE MODE button is reset
and flashes twice.
The [DVD] and [CD] REMOTE
MODE buttons are preprogrammed
with remote control codes for control-
ling Onkyo components. When one of
these buttons is reset, the prepro-
grammed code is restored.
MODE buttons are preprogrammed
with remote control codes for control-
ling Onkyo components. When one of
these buttons is reset, the prepro-
grammed code is restored.
Resetting the Remote Controller
1
While holding down the
[RECEIVER] button, press the
[L NIGHT] button for 3 seconds.
The [RECEIVER] button lights up.
[RECEIVER] button, press the
[L NIGHT] button for 3 seconds.
The [RECEIVER] button lights up.
2
Press the [RECEIVER] button
again.
The remote controller is reset and the
[RECEIVER] button flashes twice.
again.
The remote controller is reset and the
[RECEIVER] button flashes twice.