ONKYO TX-SR577 Guia Do Utilizador
40
If the impedance of any speaker is 4 ohms or more but
less than 6, set the Speaker Impedance to 4 ohms.
less than 6, set the Speaker Impedance to 4 ohms.
North American and Taiwan models do not support
speakers with an impedance of less than 6 ohms.
To use bi-amping, you must change the Speaker Type
setting. For hookup information, see page 19.
speakers with an impedance of less than 6 ohms.
To use bi-amping, you must change the Speaker Type
setting. For hookup information, see page 19.
Notes:
• When bi-amping is used, the AV receiver is able to
• When bi-amping is used, the AV receiver is able to
drive up to 5.1 speakers in the main room.
• Before you change these settings, turn down the
volume.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Speaker Settings
1
Press the [RECEIVER] button,
followed by the [SETUP] button.
followed by the [SETUP] button.
2
Use the Up and Down [
q]/[w]
buttons to select “2. Speaker
Setup”, and then press [ENTER].
Setup”, and then press [ENTER].
3
Use the Up and Down [
q]/[w]
buttons to select “2-1.Sp
Settings”, and then press
[ENTER].
Settings”, and then press
[ENTER].
If you change these settings, you must run the
Audyssey 2EQ™ Room Correction and Speaker Setup
again (see page 37).
Audyssey 2EQ™ Room Correction and Speaker Setup
again (see page 37).
4
Use the Up and Down [
q]/[w]
buttons to select “Impedance”,
and use the Left and Right
[
and use the Left and Right
[
e]/[r] buttons to select (not
North American and Taiwan
models):
4 ohms: Select if the impedance of any
models):
4 ohms: Select if the impedance of any
speaker is 4 ohms or more but
less than 6.
less than 6.
6 ohms: Select if the impedances of all
speakers are between 6 and
16 ohms.
16 ohms.
5
Use the Up and Down [
q]/[w]
buttons to select “Sp Type”, and
use the Left and Right [
use the Left and Right [
e]/[r]
buttons to select (TX-SR577
only):
Normal: Select this if you’ve
only):
Normal: Select this if you’ve
connected your front speakers
normally.
normally.
Bi-Amp:Select this if you’ve
connected your front speakers
for bi-amped operation.
for bi-amped operation.
Note:
Powered Zone2 cannot be used if “Sp
Type” is set to “Bi-Amp”.
Powered Zone2 cannot be used if “Sp
Type” is set to “Bi-Amp”.
6
Use the Up and Down [
q]/[w] but-
tons to select “SB/FH”, and then
use the Left and Right [
use the Left and Right [
e]/[r]
buttons to select (TX-SR577
only):
only):
FrontHigh:
Select this if you’ve con-
nected your front high speak-
ers to the SURR BACK L/R
terminal posts.
nected your front high speak-
ers to the SURR BACK L/R
terminal posts.
SurrBack:
Select this if you’ve con-
nected your surround back
speakers to the SURR BACK
L/R terminal posts.
nected your surround back
speakers to the SURR BACK
L/R terminal posts.
Note:
If the “Sp Type” setting is set to “Bi-
Amp”, or Powered Zone 2 is set to “Not
Act” (page 81), this setting cannot be
selected.
If the “Sp Type” setting is set to “Bi-
Amp”, or Powered Zone 2 is set to “Not
Act” (page 81), this setting cannot be
selected.
7
Press the [SETUP] button.
Setup closes.
Setup closes.