ONKYO TX-NR708 Manual Do Utilizador
28
En
Using the Easy macro command in the Easy macro mode,
you can sequentially operate Onkyo components with sim-
ple commands by simply pressing one button. The default
actions are described below. Press ACTIVITIES to start
the Easy macro command.
Once the AV receiver has entered the normal macro mode,
all of ACTIVITIES will automatically switch to the nor-
mal macro mode. In this case, pressing ALL OFF will set
only the AV receiver to Standby mode.
you can sequentially operate Onkyo components with sim-
ple commands by simply pressing one button. The default
actions are described below. Press ACTIVITIES to start
the Easy macro command.
Once the AV receiver has entered the normal macro mode,
all of ACTIVITIES will automatically switch to the nor-
mal macro mode. In this case, pressing ALL OFF will set
only the AV receiver to Standby mode.
*1
Depending on the start-up time of Blu-ray Disc/DVD player,
the AV receiver may not activate this playback command. In
the AV receiver may not activate this playback command. In
this case, press
1 on the remote controller.
Turning Off the Components
*1
When MY MUSIC is selected, with the default settings, this
will not be performed.
will not be performed.
*2
With some televisions, the power may not be turned off (or
enter standby).
enter standby).
Changing Source Component
When you want to operate the component that is not
assigned as the source component, you can assign it as the
source component.
assigned as the source component, you can assign it as the
source component.
Restoreing Default
Using Easy Macros
Press
MY MOVIE, MY TV, or MY MUSIC.
MY MOVIE (default):
1. The TV connected to the AV receiver is turned
1. The TV connected to the AV receiver is turned
on.
2. The Onkyo DVD player connected to the AV
receiver is turned on.
3. The AV receiver is turned on.
4. The input selector of the AV receiver is set to
4. The input selector of the AV receiver is set to
“BD/DVD”.
5. The player starts playback.
*1
MY TV (default):
1. The TV connected to the AV receiver is turned
1. The TV connected to the AV receiver is turned
on.
2. The cable set-top box connected to the AV
receiver is turned on.
3. The AV receiver is turned on.
4. The input selector of the AV receiver is set to
4. The input selector of the AV receiver is set to
“CBL/SAT”. You can enjoy cable TV.
MY MUSIC (default):
1. The Onkyo CD player connected to the AV
1. The Onkyo CD player connected to the AV
receiver is turned on.
2. The AV receiver is turned on.
3. The input selector of the AV receiver is set to
3. The input selector of the AV receiver is set to
“TV/CD”.
4. The player starts playback.
Note
• Once you start the Easy macro command, you cannot use
other ACTIVITIES during the execution. If you want to
operate other components halfway, press ALL OFF to
stop and press desired ACTIVITIES.
operate other components halfway, press ALL OFF to
stop and press desired ACTIVITIES.
Press
ALL OFF.
1. The connected component stops and turns off.
2. The AV receiver turns off.
3. The TV connected to the AV receiver turns off
2. The AV receiver turns off.
3. The TV connected to the AV receiver turns off
(Standby).
*1*2
While holding down
REMOTE MODE, press and
hold down
MY MOVIE, MY TV, or MY MUSIC
(about 3 seconds).
ACTIVITIES that you pressed flashes twice, indicat-
ing that the setting has been established.
Examples:
When you press MY MUSIC and want to start the
Onkyo Cassette recorder, while holding down TV/
CD, press and hold down MY MUSIC (about 3 sec-
onds) flashes twice.
ACTIVITIES that you pressed flashes twice, indicat-
ing that the setting has been established.
Examples:
When you press MY MUSIC and want to start the
Onkyo Cassette recorder, while holding down TV/
CD, press and hold down MY MUSIC (about 3 sec-
onds) flashes twice.
1
While holding down
HOME, press and hold down
ALL OFF until ALL OFF lights (about 3 seconds).
2
Release
HOME and ALL OFF and press ALL OFF
again.
ALL OFF flashes twice.
ALL OFF flashes twice.