ONKYO HT-R538 Manual Do Utilizador

En

■

`

Specify the distance from the each speaker to your lis-
tening position.

• The speaker distance setting cannot be changed while a pair of 

headphones is connected, or “Audio TV OUT” setting is set to 

“

”

 (

32) or Speakers B is on.

• Speakers that you set to “No” or “None” in the “Sp Config 

30) cannot be selected.

• The Center, Right, and Subwoofer distances can be set up to 

1.5 m more or less than the Left distance. For example, if the 
Left distance is set to 6 m, the Center, Right, and Subwoofer dis-
tances can be set between 4.5 and 7.5 m.

• The Surround distances can be set up to 1.5 m more or 4.5 m less 

than the Left distance. For example, if the Left distance is set to 
6 m, the SurrRight and SurrLeft distances can be set between 1.5 
and 7.5 m.

Here you can adjust the level of each speaker with the 
built-in test tone so that the volume of each speaker is the 
same at the listening position.

■

*1

`

–12 dB to 0 dB to +12 dB in 1 dB step.

■

*1

`

 –15 dB to 0 dB to +12 dB in 1 dB step.

• Speakers that you set to “No” or “None” in the “Sp Config 

30) cannot be selected.

• The speakers cannot be calibrated while a pair of headphones is 

connected, Speakers B is on, or “Audio TV OUT” setting is set 
to 

“

”

32) or the AV receiver is muted.

*1

For the center speaker and subwoofer, the level settings made 
by using AUDIO are saved.

• If you’re using a handheld sound level meter, adjust the level of 

each speaker so that it reads 75 dB SPL at the listening position, 
measured with C-weighting and slow reading.

With the Audio Adjust functions and settings, you can 
adjust the sound and listening modes as you like.

Multiplex
This setting determines which channel of a stereo multi-
plex source is output. Use it to select audio channels or 
languages with multiplex sources, multilingual TV broad-
casts, and so on.

■

`

:

The main channel is output.

`

Sub:

The sub channel is output.

`

M/S:

Both the main and sub channels are output.

Mono
This setting specifies the channel to be used for playing 
any 2-channel digital source such as Dolby Digital, or 2-
channel analog/PCM source in the Mono listening mode.

■

`

L+R:

Both the left and right channels are output.

`

Left:

Only the left channel is output.

`

Right:

Only the right channel is output.

PLII Music (2ch Input)
These settings apply to only 2-channel stereo sources.

■

`

On:

Panorama function on.

`

Off:

Panorama function off.

With this setting, you can broaden the width of the front 
stereo image when using the Dolby Pro Logic II Music 
listening mode.

■

`

–3 to 0 to +3

With this setting, you can move the sound field forward 
or backward when using the Dolby Pro Logic II Music 
listening mode. Higher settings move the sound field 
backward. Lower settings move it forward.
If the stereo image feels too wide, or there’s too much 
surround sound, move the sound field forward to 
improve the balance. Conversely, if the stereo image 
feels like it’s in mono, or there’s not enough surround 
sound, move it backward.

■

`

0 to 3 to 7

With this setting, you can adjust the width of the sound 
from the center speaker when using the Dolby Pro 
Logic II Music listening mode. Normally, if you’re 
using a center speaker, the center channel sound is out-
put by only the center speaker. (If you’re not using a 
center speaker, the center channel sound will be distrib-
uted to the front left and right speakers to create a phan-
tom center). This setting controls the front left, right, 
and center mix, allowing you to adjust the weight of the 
center channel sound.