Panasonic cq-rx300n Manual Do Utilizador

Pull the insulation fi lm out from 

the backside of the remote control 

gently.

Set your car’s ignition switch 
to the ACC or ON position. 

Select the radio AM mode. (

«

 “Radio (AM 

[LW/MW]/FM)”).

Press

[DISP].

(clock display)

Hold down 

[DISP] for more than 

2 seconds. 

Hour blinks

Adjust the hour. 

Hour entered

[]: sets the hour ahead. 

[]: sets the hour back.

Press

[DISP].

Minute blinks

Adjust the minute.

 Minute entered

[]: sets the minute ahead. 

[]: sets the minute back.

Press

[DISP].

Completed

• “NO CT” is displayed before adjusting the clock. 

• When a broadcast of FM Radio Data System is received, 

the clock is adjusted automatically by the Clock Time 
service.

• Hold down [] or [] to change numbers rapidly.

Note: Battery Information:

Battery Type:  Panasonic lithium battery (CR2025) (Included 

in the remote control)

Battery Life:   Approximately 6 months under normal use (at 

room temperature)

\CQ-RX400N\  \CQ-RX300N\ 

\CQ-RX400N\  \CQ-RX300N\  \CQ-RX200N\

Set your car’s ignition switch to the ACC or 
ON position. 

Press

[SRC] (PWR: Power).

The demonstration screen appears. 

\CQ-RX400N\

\CQ-RX300N\  \CQ-RX200N\ 

Hold down 

[VOL] (PUSH SEL: Select) for  

2 sec. or more to open the function menu. 

Press

[VOL] (PUSH SEL: Select) to select 

DEMO. 

Turn 

[VOL] counterclockwise. 

For using the remote control, press [0] ().

• To return to the regular mode, press [DISP].
• Refer to the section on “Function Settings”. 
• When “NO USB” (\CQ-RX400N\  \CQ-RX300N\) or “NO 

DISC” is displayed, the Demonstration cannot be cancelled.

Press

[SRC] (PWR: Power).

selects a value in the audio menu.
(PUSH SEL) (Push to select)

selects items in the audio menu.

[DISP] (Display)

exits from the audio menu.

(Setting Range: 0 to 40, Default: 18)

: Up
: Down

(Setting Range: –12 dB to +12 dB by 2 dB, Default: 0 dB)

: Increased
: Decreased

(Setting Range: –12 dB to +12 dB by 2 dB, Default: 0 dB)

: Increased
: Decreased

(Setting Range: FLAT/ROCK/POP/VOCAL/JAZZ/CLUB, Default: 

FLAT)

(

«

“Sound Control”)

(Tone/SQ adjustable range: B12 dB to A12 dB (by 2 dB))

Setting range: 

SQ Low/Bass:  ±12 dB (at 60 Hz, 80 Hz, 100 Hz, 200 Hz)

SQ Mid: 

±12 dB (at 500 Hz, 1 kHz, 2 kHz, 3 kHz)

SQ High/Treble:  ±12 dB (at 10 kHz, 12 kHz, 15 kHz, 18 kHz)

/: center frequency up/down
[] []: Band selection

[] []: Level up/down 

(Setting Range: 15 levels each, Default: CNT (centre))

: Right enhanced
: Left enhanced

(Setting Range: 15 levels each, Default: CNT (centre))

: Front enhanced
: Rear enhanced

Notes: 
• The volume can also be adjusted directly using [VOL] on the main unit. (

«

 “General”) 

• For further information on SQ (Sound Quality) settings, refer to “Sound Control”. 
• Do not activate SQ and Bass/Treble at the same time to avoid causing sound distortion.  

Press

[VOL] (PUSH SEL) to open the audio menu.

Note: If no operation takes place for more than 5 seconds in audio setting (2 seconds in the volume adjustment, 

10 seconds in the SQ adjustment), the display returns to the regular mode. 

Press

[VOL] (PUSH SEL) to select a 

mode to be adjusted.

Turn 

[VOL] clockwise or counterclockwise to 

adjust.

Notes:
\CQ-RX400N\  \CQ-RX300N\  \CQ-RX200N\
• The sequence and contents of setting items may depend 

on the conditions of devices to be connected. For further 
information, refer to the System Upgrade Guidebook or 
the instruction manuals for the devices to be connected. 

\CQ-RX200N\  \CQ-RX103N\  \CQ-RX102N\ 
\CQ-RX101N\
• If the fader is set to front, the pre-amp. output (rear) is 

decreased.

Useful functions such asAF, TA, PTY are available in the RDS (Radio Data System)-ready areas.

The following functions are available when the AF mode is 

active (

 lights).

•

When receiving conditions become bad, a station with better 
receiving conditions is automatically tuned in to.

•

When executing APM, only RDS stations are selected.

•

When calling up a preset station, a best receiving station is 
selected automatically. (BSR Best Stations Research)

•

The AF sensitivity can be adjusted.

•

The AF available range can be adjusted. (

«

 “Function 

Settings”)

The following functions are available when the TA mode is 

active (  lights).

•

A TP station is automatically searched for and received at 
the instant of toggling the TA mode on if you are receiving a 
non-TP station or TP station with poor reception. 

•

When executing station search or APM, only TP stations are 
selected.

•

Setting to TA on with the unit in another mode, it will 
automatically switch to radio mode and output the traffi c 
announcement when the traffi c announcement begins. The 
traffi c announcement having fi nished, the unit will return to 
the previous mode. (TA Standby Mode)

Hold down [TA] (AF) for more than 2 seconds to select AF 

level.

If reception becomes poor when tuning in a preset station, 

press the same preset number button. The same station with 

better reception will be searched for.

Press same preset number button again to cancel.

(blinks)

Note: For PI Seek, cancel the TA mode fi rst, then execute PI 

Seek.

The following functions are available when the PTY mode is 

active.

•

The PTY of receiving station appears.

•

Programs can be searched for by PTY.

Note: PTY language can be selected. (

«

“Function Settings”)

The clock is automatically adjusted.

As well as the frequency, the name of the broadcast station 

appears.

RDS information is updated constantly in response to the 

current position.

Traffi c information from the current and other network stations 

can be received.

Emergency announcement automatically appears on the 

display when it is received.

Some FM stations are broadcasting added data compatible with RDS. This radio set offers convenient functions using such data.

RDS service availability varies with areas. Please understand if RDS service is not available in your area, the following service is 

not available, either.

The following functions are available when receiving RDS stations.

Pressing [TA] toggles TA on and off. 

•

This operation is not adjustable by the remote control.

•

Traffi c information is available in monaural. 

•

Adjust the TA volume only while receiving a TA. 

For listening to only traffi c information, activate TA and set 

the volume to 0 in FM mode.

Once traffi c information starts, the volume changes to the 

TA volume.

Holding down [DISP] (PTY) for more than 2 seconds 

toggles PTY mode on and off.

Programs can be searched for by use of PTY that has been 

originally preset.

Press

[1] to [6] to select PTY in the PTY 

mode.

1

NEWS

NEWS

2

SPEECH

AFFAIRS, INFO, EDUCATE, DRAMA, 
CULTURE, SCIENCE, VARIED, 
WEATHER, FINANCE, CHILDREN, 
SOCIAL, RELIGION, PHONE IN, 
TRAVEL, LEISURE, DOCUMENT

3

SPORT

SPORT

4

POP M

POP M

5

CLASSICS

CLASSICS

6

MUSIC

ROCK M, EASY M, LIGHT M, 
OTHER M, JAZZ, COUNTRY, 
NATION M, OLDIES, FOLK M

Another station in the same PTY is searched for by pressing 
[BAND].

•

When there is no corresponding programme type station, 
“NONE” is displayed.

•

A desired PTY appears for 5 seconds.

•

Preset contents are changeable.

Press

[] or [] to select PTY. 

SPEECH  MUSIC  NEWS



AFFAIRS 



SPORT  EDUCATE  DRAMA 

CULTURE  SCIENCE  VARIED





ROCK M  EASY M  LIGHT M   CLASSICS 

OTHER M  WEATHER FINANCE  CHILDREN 

SOCIAL  RELIGION  PHONE IN  TRAVEL 

LEISURE  JAZZ



COUNTRY  NATION M 

OLDIES  FOLK M  DOCUMENT

Press

[BAND].

Search starts.

•

To stop searching, press [BAND] (SET).

• When there is no corresponding programme type station, 

“NONE” is displayed.

Original PTY presets can be changed as you like. 

Select a PTY that you would like to preset.

Follow the procedure of ordinary 
presetting. (

«

 “Station Preset” in “Radio 

(AM [LW/MW]/FM)”)

Low level AF operating sensitivity. (Default)

High level AF operating sensitivity.

When the AF network of an RDS station is not 

required.

Press

[DISP] to change the display.

Notes:
• For scrolling text, press [3] (SCROLL).
• “NO TEXT” is displayed when there is no information on the disc.

All the available songs (tracks/fi les) are played in a random 

sequence.

Press

[4] (RANDOM).

Press again to cancel.

All the available fi les in current folder are played in a random 

sequence.

Hold down

 [4] (RANDOM) for more than 

2 seconds.
Hold down again to cancel.

The current song (track/fi le) is repeated.

Press

[6] (REPEAT).

Press again to cancel.

The current folder is repeated.

Hold down 

[6] (REPEAT) for more than 

2 seconds. 
Hold down again to cancel.

The fi rst 10 seconds of each songs (tracks/fi les) is played in 

sequence.

Press

 [5] (SCAN).

Press again to cancel.

From the next folder, the fi rst 10 seconds of the fi rst fi le in 

each folder is played in sequence.

Hold down 

[5] (SCAN) for more than 

2 seconds.
Hold down again to cancel.

Track number

Play time

Play Mode indicators

Play Mode indicators

Lights when folder random/repeat/scan is on.

Folder number

File number

Normal

Disc title

Track title

Clock

Normal

Play time

Folder name/ 

Album*
File name/

Title, artist*
Clock

*ID3/WMA/AAC Tag On/Off
Hold down 

[3] for more 

than 2 seconds.

album title and song title/ 

artist name are displayed.

(Default)

folder name/fi le name are 

displayed.

Lights when the disc is loaded.

Press

[SRC] to select the Disc Player 

source.

Select a desired portion.

Press

[] / [].

Note: To perform fast forward/reverse, hold down either of 

them.

Previous/next track

Previous/next fi le

Press

[] / [].

Note: A disc which has both CD-DA data and MP3/WMA/AAC data on 

it may not be reproduced normally.

[] []

skip to the previous/next track/fi le in 

the player mode.

Hold down either of them for fast 

reverse/fast forward.

[] (Eject) 

ejects the disc.

[DISP] (Display)

switches the information on the display.

[] []

skip to the previous/next folder.

toggles on/off each play mode. 
[3] (SCROLL) 

scrolls the information on display.

() (Play/Pause) 

toggles pause/play in the player source.

[SRC] (Source) 
selects a source.

Printed side up

Notes: 
• Do not insert a disc when the 

• Refer to the section of “Notes on Discs” and “Notes on MP3/WMA/

• This unit does not support 8 cm discs.

• If you insert an 8 cm disc and cannot eject it, turn ACC of your car off 

once and turn it on again, then press [] (Eject).

• Do not insert foreign matter into the disc slot.

CQ-RX400N

MP3/WMA/AAC

CQ-RX300N

MP3/WMA/AAC

CQ-RX200N

MP3/WMA

CQ-RX103N

MP3/WMA

CQ-RX102N

MP3/WMA

CQ-RX101N

MP3/WMA

Press

[BAND] ().

Press again to cancel.

takes a disc in with the 

printed side facing up.

You have 6 preset modes (FLAT, ROCK, POP, VOCAL, JAZZ, 

CLUB). You can customize your settings for these and save 

them for instant recall.

Press

[VOL] (PUSH SEL:

Select) to open the audio menu.

Press

[VOL] (PUSH SEL: Select) to select 

SQ.

Turn 

[VOL] to select the sound 

type as follows. 

Press [DISP] to return to the regular mode. 

Note: Please refer to “Audio Settings” for the adjustment to 

each speaker. 

SQ (Sound Quality)

You can adjust the characteristics of the currently selected 
sound type (SQ). (

«

 Above)

It is also possible to preset up to 5 different adjusted SQs. 

Center frequency and level are adjustable in each of 3 bands. 
This lets you fi ne-tune sound quality for each genre to suit 
car-interior acoustics and your personal preferences. 

Tone/SQ adjustable range: B12 dB to A12 dB (by 2 dB)

SQ Low/Bass:

±12 dB (at 60 Hz, 80 Hz, 100 Hz, 200 Hz)

SQ Mid:

±12 dB (at 500 Hz, 1 kHz, 2 kHz, 3 kHz)

SQ High/Treble: ±12 dB (at 10 kHz, 12 kHz, 15 kHz, 18 kHz)

• The bass/treble control level of each frequency is fi xed to the 

frequency that has been selected for SQ. 

To return an adjusted SQ to the default setting 
 Select the SQ which is to be returned to the default setting.
(Follow steps 

 to 

 in “SQ Changeover”. 

«

 Above) 

 Hold down 

[BAND] for 2 sec. or more. 

Notes: 
• You cannot save any SQ presetting value in [1] button. 
• Any SQ adjustments will not change the call up screen 

names such as ROCK and JAZZ. 

• Do not activate SQ and Bass/Treble at the same time to avoid 

causing sound distortion. 

Press

[VOL] (PUSH SEL:

Select) to open the audio menu.

Press

[VOL] (PUSH SEL: Select) to select 

SQ SET.

Adjust each band. 

/: center frequency up/down
[] []: Band selection

[] []: Level up/down 

Level

Frequency

Hold down the numeric button 

[2] to [6] for 

2 sec. or more. 

•  The adjusted SQ is preset in the number of the selected 

button, and return to the regular mode resumes. 

•  SQ Adjustment will not be saved unless it is preset. Always 

preset after making adjustments. 

does not emphasize any part. (Default)

exaggerates bass and treble. 

slightly emphasizes bass and treble. 

emphasizes middle tone and slightly emphasizes 

treble.

sound with emphasis on sharpness of high-hat and 

echo saxophone.

reproduction of realism being in a club.

[VOL] (Volume)

[SRC] (Source)

selects a source.
[PWR] (Power)

toggles power on/off.

Set your car’s ignition switch to the ACC or ON position.

Power on: Press [SRC] (PWR).
Power off: Hold down [SRC] (PWR) for more 

Remote Control Sensor

(

«

 “Radio Data System 

(RDS) in FM Broadcasting”)

AUX1 Connector (3.5 mm œ stereo)

From line output of external sound/audio device (ex. Silicon-

audio player, HDD player, etc.) 

Note: The connector is labeled “AUX1”, but it appears on the 
display as “<AUX IN>”. 

(

«

Below)

• Set the volume level to low enough before the AUX 

\CQ-RX103N\  \CQ-RX102N\  \CQ-RX101N\

(Setting Range: 0 to 40, Default: 18)

Turn 

[VOL].

\CQ-RX200N\

(

«

Right)

Press

 [SRC] to change the source.

\CQ-RX400N\  \CQ-RX300N\ 

(

«

Right)

(

«

Right)

Note: Select USB Connector mode to operate the iPod 
series connected with USB connector. 

«

Note: For information about connectable devices, refer to 

the System Upgrade Guidebook or the instruction manual 

for each device.

Q

\CQ-RX400N\  \CQ-RX300N\  \CQ-RX200N\ 

Shift to connected device 
When connecting CD changer 

When connecting iPod

When connecting Bluetooth Unit 

The devices connected to the ports 1 to 4 are activated in 

sequence after shifting to AUX2 (device connected to the 

AUX terminal of the expansion module).

Q

\CQ-RX400N\  \CQ-RX300N\ 

When loading MP3/WMA/AAC data 

\CQ-RX400N\  \CQ-RX300N\  \CQ-RX200N\

AUX IN*: 
\CQ-RX400N\  \CQ-RX300N\  \CQ-RX200N\ 

\CQ-RX103N\  \CQ-RX102N\  \CQ-RX101N\

selects a band in the radio source.
[APM] (Auto Preset Memory)

executes APM in the radio source. (Hold it 

down for more than 2 seconds.)

[SRC] (Source)

selects a source.

Preset buttons [1] to [6]

selects a preset station in the radio source,

and presets the current station. (Hold it down for more than 2 seconds.)

[TUNE ] [TUNE ]

down/up the frequency. (Hold it down for more 

than 0.5 seconds and release it for seek tuning.)

[DISP] (Display)

switches the information on the 

display.

Press

[SRC] to select the radio source.

Press

[BAND] to select a band.

Select a station.

Band/

frequency

CT (Clock 

Time)

lights while receiving an FM 

stereo signal.

Band

Frequency

Preset Number

[TUNE ]: Lower

[TUNE ]: Higher
Note: Hold down for 0.5 sec. or more and release for station 

search.

Press the corresponding preset button from 

to

[6] to tune in a preset station.

Up to 6 stations can be preset in AM, FM1, FM2, and FM3 respectively.

Preset stations can be simply called up by pressing [1] to [6].

With this operation, stations with good receiving conditions 

can be automatically stored in the preset memory.

Select a band.

Hold down 

[BAND] (APM) for more than 

2 seconds.

The preset stations under best receiving conditions are received 

for 5 seconds each after presetting the stations (SCAN). To stop 

scanning, press one of the buttons from [1] to [6].

Note: New stations overwrite existing saved stations. 

Tune into a station.

Hold down one of the preset buttons from 
[1] to [6] for more than 2 seconds. 

(blinks once)

Note: New stations overwrite existing saved stations.

Band/

frequency

PS

CT

PS (Programme 

Service name)

Band/frequency

CT

Press

[DISP] to change the display.

selects a value in the function menu.
(PUSH SEL) (Push to select)

selects items in the function menu.

[DISP] (Display)

exits from the function menu.

FM Monaural [FM]

: MONO ON

(

 lights.)

Noise is signifi cantly decreased when weak signals are 

received from an FM broadcast station.

: MONO OFF 

(Default)

FM Local [FM]

: LOCAL ON

(

 lights.)

Only stations with good reception are detected in seek 

tuning.

: LOCAL OFF

(Default)

AM Local [AM]

: LOCAL ON

(

 lights.)

Only stations with good reception are detected in seek 

tuning.

: LOCAL OFF

(Default)

Region ]RDS]

: The 

frequency is 

changed only for 

programs within 

the region.

Note: When the Region mode is switched from OFF to 

ON or vice versa, the AF mode turns on automatically.

: The 

frequency is 

changed also 

for programs 

outside the 

region. (Default) 

PTY Language 
]RDS]

: English 

(Default)

: Swedish

(

«

Continued below)

Hold down 

[VOL] (PUSH SEL) for 2 sec. or more to open the function menu.

Note: If no operation takes place for more than 5 seconds in function setting, the display returns to the regular mode. 

Press

[VOL] (PUSH SEL) to select a 

mode to be adjusted.

Turn 

[VOL] clockwise or counterclockwise to 

adjust.

A track (CD mode), fi le, folder (MP3/WMA/AAC mode) can 

be directly selected.
Example: Track number 5

Press

[#] (NUMBER).

Press

[5].

Press

[BAND] (SET).

Notes:
• To suspend direct selection, press [DISP].
• For folder selection, enter a number after pressing [#]

(NUMBER) twice.

The following functions are not available on remote control 

unit.

• Scroll

• Disc eject

• Tag on/off

Remove the battery holder with 

the remote control unit placed on 

a fl at surface.
 Stick your thumbnail into 

the groove, and push the 

holder in the direction of 

the arrow, and at the same 

time.

 Pull it out in the direction 

of the arrow using a tough 

pointed object.

Notes:
• This instruction manual explains operations for use with the buttons on the main unit. (Different operations excluded)
• Aim the remote control at the remote sensor and operate it.

selects a preset station (1 to 6), 

presets the current station (Hold it down for more than 

2 seconds.), 

inputs the number in direct selection.
[#] (NUMBER)

executes the direct selection.
[RANDOM] [SCAN] [REPEAT]

toggles on/off each play mode.
[] []

down/up the frequency (Hold it down for more than 

0.5 seconds and release it for seek tuning.)
[] []

skip to the previous/next folder in player mode.
[] []

skip to the previous/next track/fi le in player mode. Hold

it down for fast reverse/fast forward.

selects a band in the tuner source, toggles pause/play in player source, 

executes the APM (Auto Preset Memory) in tuner source 

(Hold it down for more than 2 seconds).

[MENU] (SEL: Select)

selects the items in the audio menu.

[VOL] (volume)

adjusts the volume, and selects the 

value in the audio menu, etc.

toggles mute on/off. 
(Only for remote control unit) 
Note: You can select mute or 

attenuation. (

«

 “Function Settings”)

[DISP] (Display)

switches the information on display, 

and exits the audio menu.

selects a source.
(POWER)

toggles power on/off.

Batteries and insulation fi lm can be ingested, so keep 

them out of the reach of infants. If an infant ingests a 

battery or insulation fi lm, please seek immediate medical 

attention.

• Remove and dispose of an old battery immediately.
• Do not disassemble, heat or short a battery. Do not 

throw a battery into a fi re or water.

• Follow local regulations when disposing of a battery.
• Improper use of batteries may cause overheating, an 

explosion or ignition, resulting in injury or a fi re.

Notes: Battery Information:

Battery Type:  Panasonic lithium battery (CR2025) (Included 

in the remote control)

Battery Life:    Approximately 6 months under normal use (at 

room temperature)

Tough pointed object

Back side

1

2

  Put a battery in the 

case with (+) side 

facing up.

  Put the case back.





\CQ-RX400N\  \CQ-RX300N\ 

: On (Default)

\CQ-RX400N\  \CQ-RX300N\  \CQ-RX200N\ 

You can set up the monitor to display or hide the 

demonstration screen.

Note: Button operation with either the main unit or 

remote control allows users to cancel the demonstration 

screen for 20 seconds and enable the selected operation 

even in the demo-on mode. 

: Off

: Volume down 

by 10 steps

You can select mute or attenuation.

: Volume off 

(Default)

\CQ-RX400N\  \CQ-RX300N\
\CQ-RX200N\

: On (Skip 

disabled.)

(Default)

If AUX1 is not used, the AUX1 mode is skipped when 

selecting the source. 

: Off (Skip 

enabled.)

\CQ-RX103N\  \CQ-RX102N\
\CQ-RX101N\

: On (Skip 

disabled.)

(Default)

If AUX is not used, the AUX mode is skipped when 

selecting the source. 

: Off (Skip 

enabled.)

Notes:
• To return to the regular mode, press [DISP].
\CQ-RX400N\  \CQ-RX300N\  \CQ-RX200N\
• The sequence and contents of setting items may depend on the conditions of devices to be connected. For further 

information, refer to the System Upgrade Guidebook or the instruction manuals for the devices to be connected.