EarthQuake 9010140 Manual Do Utilizador
Page 12
GetEarthquake.com
1-800-345-6007
ATTACHINg HOPPeR exTeNSION TO HOPPeR
For european models only (9050140, 9060140, and
9010140)
Tools Required:
Tools Required:
5/32” Hex drive wrench (i.e: allen wrench)
7/16” Wrench for 1/4-20 flange nut
NOTe: Assemble extension before adding fuel or engine oil.
To attach the hopper extension:
1) Before bolting the handle into position, slide one hopper ex-
1) Before bolting the handle into position, slide one hopper ex-
tension half (1709470) over the rim of the hopper. The groove
around the inside bottom of the hopper extension should fit
over the rim around the top of the hopper. See FIgURe 22.
2) Ensuring the hopper and hopper extension holes are now
aligned along the top rim of the hopper, place a 1/4-20 x 3/4
bolts (1960507) through each of the four holes in the extension
and hopper. Secure bolts in place with the included 17/64 x 5/8
flat washers (1921319) and 1/4-20 flange nuts (1930642). DO
NOT fully tighten hardware at this point. See FIgURe 22.
3) Bolt handle into position using appropriate hardware. Lay the
unit down, resting the handle on a piece of cardboard to pre-
vent scratching.
4) Follow Step 1 to install the second extension half to the opposite
side of the hopper. Again, the bottom groove of the hopper
extension should fit over the rim at the top of the hopper. Align
the bolt holes between the top of the hopper and bottom of the
hopper extension and insert hardware. See FIgURe 23.
5) Place a 1/4-20 x 3/4 bolt (1960507) in each of the three holes
along the two seams of the joined hopper extension halves.
Secure each bolt with a flat washer and flange nut. DO NOT
fully tighten. See FIgURe 24.
fully tighten. See FIgURe 24.
6) Place bolt through each of the two holes on top of the joined hopper
extension. Secure with flat washer and flange nut. See FIgURe 25.
7) Once all hardware has been inserted, use 5/32” allen wrench and
7/16” wrench to fully tighten all hardware, including those around
hopper rim and along the hopper extension seams.
1/4-20 bolt
hopper extension
BALLOON #
N
O
I
T
P
I
R
C
S
E
D
#
T
R
A
P
CE/QTY.
6
1
N
Z
K
L
B
H
B
S
4
/
3
X
0
2
-
4
/
1
T
L
O
B
7
0
5
0
6
9
1
1
2
2
1930642
NUT 1/4-20 HFLTPLK BLK ZN
16
2
E
C
R
E
P
P
O
H
R
E
P
P
I
H
C
N
O
I
S
N
E
T
X
E
0
7
4
9
0
7
1
3
hopper extension
1/4-20 bolt
flange nut
flange nut
flat washer
flat washer
1/4-20 bolt
hopper extension
BALLOON #
N
O
I
T
P
I
R
C
S
E
D
#
T
R
A
P
CE/QTY.
6
1
N
Z
K
L
B
H
B
S
4
/
3
X
0
2
-
4
/
1
T
L
O
B
7
0
5
0
6
9
1
1
2
2
1930642
NUT 1/4-20 HFLTPLK BLK ZN
16
2
E
C
R
E
P
P
O
H
R
E
P
P
I
H
C
N
O
I
S
N
E
T
X
E
0
7
4
9
0
7
1
3
hopper extension
1/4-20 bolt
flange nut
flange nut
flat washer
flat washer
Figure 22
Figure 23
2
3
1
3
1/4-20 bolt
1/4-20 bolt
1/4-20 bolt
Figure 24
2
3
1
3
1/4-20 bolt
1/4-20 bolt
1/4-20 bolt
1/4-20 bolt
Figure 25