Yamaha PM5D-RH V2 Manual Do Utilizador
6
Output channel operations
62
PM5D/PM5D-RH V2 / DSP5D Owner’s Manual
Operating section
❏ Sending signals from the STEREO A/B
channels to output jacks
Here’s how the signals sent from input channels or MIX
channels to the STEREO bus can be output from STEREO
OUT jacks A/B.
channels to the STEREO bus can be output from STEREO
OUT jacks A/B.
1
Make sure that appropriate signals are being
sent from the desired channels to the STEREO
bus.
sent from the desired channels to the STEREO
bus.
2
Turn on the STEREO [ON] key of the STEREO
A/B channel strip.
A/B channel strip.
3
Raise the [STEREO A]/[STEREO B] faders.
The signal of the STEREO A/B channels will be output
from STEREO OUT jacks A/B. The output level of the
STEREO A/B channels is shown by the [MASTER]
meters in the meter section.
The signal of the STEREO A/B channels will be output
from STEREO OUT jacks A/B. The output level of the
STEREO A/B channels is shown by the [MASTER]
meters in the meter section.
Hint
Normally, the same signal is output from the STEREO A and
B channels. However you can also use the STEREO B chan-
nel as a Center channel for L/C/R three-channel playback
(
B channels. However you can also use the STEREO B chan-
nel as a Center channel for L/C/R three-channel playback
(
❏ Sending signals from the STEREO A/B
channels to MATRIX buses
Here’s how the signal of the STEREO A/B channels can be
sent to the MATRIX buses.
sent to the MATRIX buses.
1
Make sure that an appropriate signal is being
input to the STEREO bus.
input to the STEREO bus.
2
Repeatedly press the [MATRIX/ST] key of the
DISPLAY ACCESS section to access the
MATRIX/ST ROUTING screen.
DISPLAY ACCESS section to access the
MATRIX/ST ROUTING screen.
3
Use the left/right scroll bar to display the STE-
REO A/B channels, and click the MIX TO
MATRIX ON/OFF button to turn it on.
With these settings, the signal of the STEREO A/B
channels will be sent to the MATRIX channels.
REO A/B channels, and click the MIX TO
MATRIX ON/OFF button to turn it on.
With these settings, the signal of the STEREO A/B
channels will be sent to the MATRIX channels.
4
Make sure that the STEREO A/B [ON] keys are
turned on in the STEREO A/B channel strip;
then hold down the STEREO A [SEL] key or
STEREO B [SEL] key.
While you continue holding down the key, all
MATRIX [SEL] keys will blink. In this condition, you
can use the MATRIX encoders to adjust the signal lev-
els sent from the STEREO A or B channel to the
MATRIX buses.
turned on in the STEREO A/B channel strip;
then hold down the STEREO A [SEL] key or
STEREO B [SEL] key.
While you continue holding down the key, all
MATRIX [SEL] keys will blink. In this condition, you
can use the MATRIX encoders to adjust the signal lev-
els sent from the STEREO A or B channel to the
MATRIX buses.
5
While continuing to hold down the STEREO A
[SEL] key or STEREO B [SEL] key, turn MATRIX
encoders 1–8 to adjust the signal level sent to
the MATRIX buses.
The LEDs around the periphery of the MATRIX
encoder indicate the approximate send level. When
you take your hand off the STEREO A [SEL] key or
STEREO B [SEL] key, the MATRIX encoders will
revert to their previous function.
[SEL] key or STEREO B [SEL] key, turn MATRIX
encoders 1–8 to adjust the signal level sent to
the MATRIX buses.
The LEDs around the periphery of the MATRIX
encoder indicate the approximate send level. When
you take your hand off the STEREO A [SEL] key or
STEREO B [SEL] key, the MATRIX encoders will
revert to their previous function.
Hint
• You can also switch to the above state by rapidly pressing
the STEREO A [SEL] key or STEREO B [SEL] key twice. To
return to the previous state, press any [SEL] key.
return to the previous state, press any [SEL] key.
• Send levels from the STEREO A/B channels to the MATRIX
buses can also be adjusted from within the display
(
(
➥ p.262).
Operations in the STEREO A/B chan-
nel strip
nel strip
MASTER meters
MIX TO MATRIX
ON/OFF buttons
ON/OFF buttons
MATRIX/ST ROUTING