Yamaha EMX68s Manual Do Utilizador
14
Front and rear panel
EMX88S/EMX68S—Owner’s Manual
Input/output panel
1
Channel input jacks (Hi-Z, Low-Z)
1–6 (EMX88S), 1–4 (EMX68S)
These are the input jacks for channels
1–6 (EMX88S), 1–4 (EMX68S).
1–6 (EMX88S), 1–4 (EMX68S)
These are the input jacks for channels
1–6 (EMX88S), 1–4 (EMX68S).
By using the PAD switches (control panel 6) you
can connect any of the jacks to a wide range of
sources from mics to line level devices (synthesiz-
ers or rhythm boxes etc.). The Low-Z jacks can
provide +15 V phantom power, allowing you to
use condenser microphones.
can connect any of the jacks to a wide range of
sources from mics to line level devices (synthesiz-
ers or rhythm boxes etc.). The Low-Z jacks can
provide +15 V phantom power, allowing you to
use condenser microphones.
Both Hi-Z and Low-Z are balanced, and are com-
patible with microphones of output impedance
50–600
patible with microphones of output impedance
50–600
Ω
or line level devices of 600
Ω
. The nom-
inal input level is from –40 dB to –10 dB for the
Hi-Z jacks, and from –50 dB to –20 dB for the
Low-Z jacks.
Hi-Z jacks, and from –50 dB to –20 dB for the
Low-Z jacks.
Pin connections for the Hi-Z and Low-Z jacks are
as follows.
as follows.
2
Super Hi-Z jacks
These two phone jacks are the input connectors
for input channel 5–6 (EMX88S), 3–4 (EMX68S).
They are unbalanced, can be used simulta-
neously, and their high input impedance makes
them ideal for use with instruments such as elec-
tric-acoustic guitar and electric bass. They can
also be used with line-level sources, such as syn-
thesizers and drum machines.
These two phone jacks are the input connectors
for input channel 5–6 (EMX88S), 3–4 (EMX68S).
They are unbalanced, can be used simulta-
neously, and their high input impedance makes
them ideal for use with instruments such as elec-
tric-acoustic guitar and electric bass. They can
also be used with line-level sources, such as syn-
thesizers and drum machines.
3
Channel input jacks (MIC/LINE)
7–8 (EMX88S), 5–5 (EMX68S)
These are the input jacks for channels
7–8 (EMX88S), 5–6 (EMX68S).
7–8 (EMX88S), 5–5 (EMX68S)
These are the input jacks for channels
7–8 (EMX88S), 5–6 (EMX68S).
Connect microphones to the MIC jacks. Connect
line-level devices, such as synthesizers to LINE L
(MONO)/R jacks if the devices are stereo sound
sources. Use the LINE L (MONO) jack if the
devices are monaural sound sources. The MIC
jacks can provide +15 V phantom power, allow-
ing you to use condenser microphones.
line-level devices, such as synthesizers to LINE L
(MONO)/R jacks if the devices are stereo sound
sources. Use the LINE L (MONO) jack if the
devices are monaural sound sources. The MIC
jacks can provide +15 V phantom power, allow-
ing you to use condenser microphones.
The MIC jacks are balanced, and are compatible
with microphones of output impedance 50–
600
with microphones of output impedance 50–
600
Ω
.
The LINE jacks are unbalanced, and are compati-
ble with line level devices of 600
ble with line level devices of 600
Ω
output imped-
ance. Nominal input level is –50 dB for the MIC
jacks and –10 dB for the LINE jacks.
jacks and –10 dB for the LINE jacks.
2
1
6
5
7
3
4
Low-Z jacks
(XLR type)
Hi-Z jacks
(TRS phone jacks)
Pin 1: ground
Sleeve: ground
Pin 2: hot (+)
Tip: hot (+)
Pin 3: cold (–)
Ring: cold (–)
Note: It is not possible to simultaneously use
both the Hi-Z and Low-Z inputs of a given
channel. For each channel, use only one of the
inputs as appropriate for the input source.
Phantom power is switched on/off in simulta-
neously for channels 1–8 (EMX88S), 1–6
(EMX68S). For this reason, devices which do
not require phantom power must be connected
to the Hi-Z or LINE jacks if the PHANTOM
switch (control panel L) is on.
both the Hi-Z and Low-Z inputs of a given
channel. For each channel, use only one of the
inputs as appropriate for the input source.
Phantom power is switched on/off in simulta-
neously for channels 1–8 (EMX88S), 1–6
(EMX68S). For this reason, devices which do
not require phantom power must be connected
to the Hi-Z or LINE jacks if the PHANTOM
switch (control panel L) is on.
GND
R
S
T
+
-
GND
+
-
Note: The MIC and LINE inputs for channel
7 (EMX88S), 5 (EMX68S) can be used simulta-
neously but their levels cannot be adjusted sep-
arately (Same for channel 8 (EMX88S),
6 (EMX68S).)
7 (EMX88S), 5 (EMX68S) can be used simulta-
neously but their levels cannot be adjusted sep-
arately (Same for channel 8 (EMX88S),
6 (EMX68S).)