IBM 61Y Manual Do Utilizador
Installing options
63
Attention:
Do not remove a hot-plug adapter before performing the operating-
system-defined procedure for disabling the hot-plug PCI slot that
contains the adapter. Failure to do so might cause the system to lock up.
Refer to the operating system documentation.
system-defined procedure for disabling the hot-plug PCI slot that
contains the adapter. Failure to do so might cause the system to lock up.
Refer to the operating system documentation.
1.
Remove the top cover (see “Removing the top cover” on page 59).
2.
Determine which expansion slot you will use for the adapter.
Note:
You can install hot-plug PCI adapters in PCI slots 3-6 only.
3.
Disable the selected PCI slot from the operating system. (Refer to the
documentation that comes with the operating system for information about
disabling a hot-plug PCI slot.) Disabling the PCI slot turns off the power light for
that PCI slot.
documentation that comes with the operating system for information about
disabling a hot-plug PCI slot.) Disabling the PCI slot turns off the power light for
that PCI slot.
Attention:
Make sure the power light for the hot-plug PCI slot is off before you
continue with the next step.
continue with the next step.
4.
Remove the expansion-slot cover:
a.
Rotate the adapter retention latch counterclockwise.
b.
Lift the tab covering the top of the expansion-slot cover and then remove the
expansion-slot cover from the server. Store it in a safe place for future use.
expansion-slot cover from the server. Store it in a safe place for future use.
c.
Press on the rear adapter retention latch (near the hard disk drives) as
indicated by the arrow on the latch and lift it to the open position.
indicated by the arrow on the latch and lift it to the open position.
Attention:
You must install expansion-slot covers on all empty slots. This
maintains the electromagnetic emissions characteristics of the system and
ensures proper cooling of system components.
ensures proper cooling of system components.
5.
Refer to the documentation that comes with the adapter for any cabling
instructions. It might be easier for you to route any cables before you install the
adapter.
instructions. It might be easier for you to route any cables before you install the
adapter.
6.
Remove the adapter from the static-protective package.
Attention:
Avoid touching the components and gold-edge connectors on the
adapter. If you need to put down the adapter, place the adapter,
component-side up, on a flat, static-protective surface.
adapter. If you need to put down the adapter, place the adapter,
component-side up, on a flat, static-protective surface.
7.
Install the adapter:
a.
Carefully grasp the adapter by its top edge or upper corners, and align it with
the expansion slot on the processor board.
the expansion slot on the processor board.
b.
Press the adapter firmly into the expansion slot.
Attention:
When you install an adapter in the server, be sure that it is
completely and correctly seated in the processor-board connector.
Incomplete insertion might cause damage to the processor board
or the adapter.
completely and correctly seated in the processor-board connector.
Incomplete insertion might cause damage to the processor board
or the adapter.
c.
Lower the tab over the top corner of the adapter. Rotate the adapter retention
latch clockwise until it snaps into place.
latch clockwise until it snaps into place.
d. Lower the rear adapter retention latch (near the hard disk drives) over the top
of the adapter and press on the indentation on the latch until the latch snaps
into place.
into place.
8.
Connect any needed cables to the adapter.
9.
Enable the PCI slot from the operating system. (Refer to the documentation that
comes with the operating system for information about enabling a hot-plug PCI
slot.) Make sure that the power light for the hot-plug PCI slot is on.
comes with the operating system for information about enabling a hot-plug PCI
slot.) Make sure that the power light for the hot-plug PCI slot is on.
10. If you have other options to install or remove, do so now; otherwise, go